CLASS RACER FORUM
Page 4 of 12 « First 23 4 56 Last »
Show 40 post(s) from this thread on one page

CLASS RACER FORUM (https://classracer.com/classforum/index.php)
-   Class Racer Builds (https://classracer.com/classforum/forumdisplay.php?f=58)
-   -   C4 Corvette build for Superstock I-J-K (https://classracer.com/classforum/showthread.php?t=65013)

Ernie Neal 01-29-2017 08:04 PM
Re: C4 Corvette build for Superstock I-J-K
 
Quote:
Originally Posted by jims5600 (Post 525369)
Ernie you are doing a awesome job! I have had 4 C4 street cars and have
a soft spot in my heart for those. Really like the fact you made up a spindle.
Well done.
It is great that you have all these photos of your build. Not just for us to
look over and drool! Will be nice to show people when the time comes to
sell and move on.
Best of luck on this build
Jimmy
thanks Jimmy, stay tuned through the completion of the build.

Ernie Neal
SS354

Ernie Neal 01-30-2017 11:01 AM
Re: C4 Corvette build for Superstock I-J-K
 
9 Attachment(s)
Top bar of wheelie bar assembly (yes it's a single)
Transmission in place along with Browell housing
Developed my own offset distributor mount (can make you one!)
jesel or msd styles
next is the transmission mount
the modified ART shock mount
rear end housing painted up
driveshaft loop
and under shot of tubs

Ernie Neal 01-31-2017 07:15 AM
Re: C4 Corvette build for Superstock I-J-K
 
9 Attachment(s)
motorplate after polishing
wheelie bar partially chromed
headers after I polished them
volt meter under gas door
single wheelie bar
clutch
inside after trim blacked
front spindle shot

Robert Simpson 01-31-2017 07:59 AM
Re: C4 Corvette build for Superstock I-J-K
 
Ernie, great build I like the layout. Would you happen to have any pictures of the clutch linkage installed? I am thinking that you are using a bell crank under the floor pan or under the dash dropping down to the clutch fork?

Thanks

Ernie Neal 01-31-2017 10:36 AM
Re: C4 Corvette build for Superstock I-J-K
 
2 Attachment(s)
Quote:
Originally Posted by Robert Simpson (Post 525515)
Ernie, great build I like the layout. Would you happen to have any pictures of the clutch linkage installed? I am thinking that you are using a bell crank under the floor pan or under the dash dropping down to the clutch fork?

Thanks
Robert,
my clutch linkage is inside the car similar to what old 55-57 Chevys were. I had 1 shot of one of the ends I made to hold the cross shaft. I used bearings on each end. These are welded to the dash bar. The rod drops through the floor just past the accelerator pedal.

The other picture is all the pieces that comprise the linkage before welding.

Ernie

MR DERBY CITY 01-31-2017 06:46 PM
Re: C4 Corvette build for Superstock I-J-K
 
Will you be able to find a midget in the Columbus area to crawl around the bars inside of the car to glue the carpet in ? Perhaps some one that lost their job with the B and B circus ? LOL........

Ernie Neal 01-31-2017 07:31 PM
Re: C4 Corvette build for Superstock I-J-K
 
Quote:
Originally Posted by MR DERBY CITY (Post 525571)
Will you be able to find a midget in the Columbus area to crawl around the bars inside of the car to glue the carpet in ? Perhaps some one that lost their job with the B and B circus ? LOL........
Come on M J, I was the midget. I do have to figure out the front part, more than likely need your help, again!!

Ernie

MR DERBY CITY 01-31-2017 07:52 PM
Re: C4 Corvette build for Superstock I-J-K
 
Quote:
Originally Posted by Ernie Neal (Post 525573)
Come on M J, I was the midget. I do have to figure out the front part, more than likely need your help, again!!

Ernie
Oh,....so glad to hear that your health is improving......

Ernie Neal 01-31-2017 08:09 PM
Re: C4 Corvette build for Superstock I-J-K
 
Quote:
Originally Posted by MR DERBY CITY (Post 525578)
Oh,....so glad to hear that your health is improving......
thanks M J, I feel good only sore. Tomorrow will be 3 weeks. I might get to drive after my doctor visit tomorrow.

Ernie

Ernie Neal 02-01-2017 09:24 AM
Re: C4 Corvette build for Superstock I-J-K
 
9 Attachment(s)
Well, these photos are mostly of final assembly of a lot of underhood components. Had to make that tight fitting cranktrigger bracket on the drivers side.


All times are GMT -4. The time now is 02:47 PM.
Page 4 of 12 « First 23 4 56 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright Class Racer.com. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.