CLASS RACER FORUM

CLASS RACER FORUM (https://classracer.com/classforum/index.php)
-   Stock and Super Stock Tech (https://classracer.com/classforum/forumdisplay.php?f=4)
-   -   Car will not start. (https://classracer.com/classforum/showthread.php?t=69974)

ss3011 05-24-2018 04:38 PM

Re: Car will not start.
 
Just wondering if this combination ever ran . Is this a completely new built engine / wiring / controller ? My L99 with a Big Stuff controller ran flawlessly , I do remember that the wiring on the pickup needed to be changed to work . These modifications are spelled out on the Big Stuff website . Good luck !

ss3011 05-24-2018 06:12 PM

Re: Car will not start.
 
Looked this information up on the Big Stuff website

The wire colors are different from MSD to Big Stuff for the Crank Trigger Pickup Sensor

The MSD purple wire should be hooked to the Big Stuff Black wire
The MSD Green wire should be hooked to the Big Stuff Red wire

Also there is a ground wire from the Big Stuff Harness with a loop terminal , it needs to be attached directly to the engine block . There should be a very good ground wire going from the battery to the block .

Special notice , Damage could occur to the controller if there is battery voltage to the harness, and the connectors are removed from the controller . TURN OFF the master disconnect switch before the connectors are removed or connected to the Big Stuff Controller .

If you can communicate with the controller with your laptop , you can set up a "dash board" that can let you add a tach signal . If you have no signal , then it will never start .

Good Luck !

Bobby DiDomenico 05-25-2018 08:04 AM

Re: Car will not start.
 
Quote:

Originally Posted by buzzinhalfdozen (Post 563735)
After reading back through the posts I'm going to say you're running an MSD ignition box, hooked to the big stuff controller for the EFI side of things is this correct? And if so and you have no spark...look at the MSD part only for now, if the MSD has no spark then you probably aren't producing a tach signal for the big stuff system to work off of.

Been awhile, I recall being able to trigger the MSD without the engine running to check for spark. Can you do that with yours?

Different subject, I also learned in my after high school job not to spin a magneto while carrying it with your hand on top...

buzzinhalfdozen 05-25-2018 08:35 AM

Re: Car will not start.
 
Quote:

Originally Posted by Bobby DiDomenico (Post 563772)
Been awhile, I recall being able to trigger the MSD without the engine running to check for spark. Can you do that with yours?

Different subject, I also learned in my after high school job not to spin a magneto while carrying it with your hand on top...

If he is set up in the manner I suggested, yes he can trigger the MSD with either an MSD tester or even a paper clip. That's where I was heading but not sure yet exactly what he has.

Nmbr1GMfan 05-25-2018 08:40 AM

Re: Car will not start.
 
Quote:

Originally Posted by Bobby DiDomenico (Post 563772)
Different subject, I also learned in my after high school job not to spin a magneto while carrying it with your hand on top...

I also learned this lesson the hard way!

Lenny5160 05-25-2018 12:23 PM

Re: Car will not start.
 
Quote:

Originally Posted by Nmbr1GMfan (Post 563777)
I also learned this lesson the hard way!

Never handled a magneto, but the first time I tried to move the timing on a running racecar, I just grabbed the distributor cap with my palm across the top of all the wires.

Kevin Panzino 05-28-2018 09:44 AM

Re: Car will not start.
 
What did you find, Ron/Jason?

TinSoldier 3215 05-28-2018 03:25 PM

Re: Car will not start.
 
Kevin. It was a burn wire behind the ignition box. Thanks


All times are GMT -4. The time now is 09:53 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright Class Racer.com. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.