[Cglrcng]

Ok, if you have read my novel so far and are still with me...This is the rest of the story....The major changes, the why's, when's, and what for's...On the Struggle Bus, and off to an OK Start by Thursday Oct. 5, 2023! (Not great, but OK, it still never saw a 16 sec Pass, but only because it was not forced to...).

When I re-installed the engine. I Put a brand new cam...at least new to me (a custom ground 1 off Reed Cam from GA), that was a National Record holder in an EF/S Stick Manual Truck w/ a 2.2L/135 that set both ends of the record in 2003. That cam has a ton of overlap & duration (but no cam card, I only know it is, a 106 CL cam, and it measures .444E/.432I (my max Spec lift is .445/.445), with a solid adj. lifter at the retainer w/ zero lash set (it has some really funky lobes), it really made the car sound alive and mean as can be, but in reality I do not currently have a loose enough converter to make it work yet. (Mine can be loosened a lot according to the MFG, without affecting the efficiency, as they tightened it up before they sold it to me in 94' for my not much done combo).

It was installed at 3 degrees Adv. when I went to Las Vegas for the first quarter mile passes, and 1 pass in I realized I brought everything except my spare cams, and it was a dead dog turtle on the leave, and at 100' out it started screaming as it came alive in the torque curve. It also had zero vacuum at idle, and until 3,000 RPM it was just starting to build vacuum slowly, (so it really was not playing nice with my power assist brake booster and master cyl., and I could not foot brake stall the car higher than 3,200 RPM). It was horrible.

I knew it was not the cam for this combo right now (but will be soon enough). So, while it was a double Bracket points race in Las Vegas for the Summitt Bracket Racing Series, and not a Stock Elim. race I determined I would put the car in "Drive" and let it shift itself, and slow it down as much as I could...Gonna make em wait, then make em' wait longer.

As can be seen by pics I posted at that event 18.72 was the final dial in used in 114 degree temps and corrected Alt. was measuring over 6,000 ft. plus that weekend in Vegas. (But it is a 17.45 Index in EF/S). Yeah, I get a lil' Index correction there, but not that much.

Ok, so a full review of old and new data commenced (talking about mainly data from 1993 - 1997, and my cam choices were 3 others I have on the shelf at home), but I knew I was losing at least 1/2 sec in the first 60-70', more in the 330, and more in the 660, and unless you get a slow roller up and moving early, you can never make that back no matter how much it is screaming out the back door), I decided on one, changed it, dialed in the cam, and ckd. the lift again properly. I took 2 of those cams back up to Boulder City that Monday to change the cam, restore the Power Brake System, change the injector, F.P Regulator, add ballast to my weight box to meet min. wt, and a couple of other minor changes.

By Tuesday AM I was finished....I was the only one in our group that purchased the Test n Tune Wednesday and lanes opened at Noon, closing at 6 PM...@ 12:35 PM Oct 4, I ran 1 pass (the timing was way off, rich, and flat not right at all), it ran like crap and was very slow 12:35 PM R.T. -.499 Red, 60' 2.700, 330 8.610, 1/8 13.792@ 45.31 MPH (book is 10.80 1/8 mile),1,000 18.711, 1/4...23.492@ 44.42 out of it it ran so bad on top end.

I then took a biig swing low on timing first....@ 3:39 PM Oct 4 R.T. a closer but still off -.053, 60' 2.852, 330 8.682, 1/8th 13.478@ 52.07, 1,000 17.426, and 1/4...20.699 @ 68.14

Here I decided to pull all 4 plugs (all 4 were ultra rich, remove and swap back in the stock injector), cleaned the plugs, regapped them from .035 to. 040, and decided to go back up to the timing that makes everyone cringe 43-46 degrees total (you see it has a hall effect distro, the Power Module usually controls spark, but we changed that and took the spark control away from that fender mounted computer in 1995, by adding in a Mopar Electronic Control Module from a 1983 Carbed Dodge Omni incl the wiring harness and aftermarket coil. So, we set static timing, and the box controls the total, and each cam is different in what makes them happy).

It sounds hard starting, but it needs the total high to be happy and run under index. I had made those changes already, time is getting short, it is about 5:00 PM at this poing and John Irving and his Son Jon were no doubt getting worried at this point since they witnessed so far nothing but slow running in Las Vegas and here at Bakersfield so far...Though I knew I was on the right track so far, and reversing a couple of changes was all that was needed, and all but 1 was completed almost....John and Jon came over and asked if Jon could help (I welcomed it), what I really needed was a butt in the seat, so I could take my time & set the timing properly, swing the other way for the fences.

He did, we started it, I cranked in 43 degrees total (that was equal to 21 initial static, and I told him I was going to control the throttle, just hold the brakes hard. And I nearly laid it on the rev limiter...and she sounded right!

I took it for the last pass of the day after thanking them....@ 5:28 PM 4 Oct. R.T. a right on just what I was looking for .012 Green, 60' 2.379, 330 7.065, 1/8 10.992@ 62.84, 1,000 14.444, (it then hit the rev limiter at 7,300 RPM slowing the pass down ( I thought it would be out the back door in 2nd. gear, not quite....1/4 in 17.721 @ 65.47 and down because I need to shift it before 7,300. But I knew first pass in the morning at that point Q1 of race 1 would be under, just not by how much yet. I assured them I only need to re-learn how to shift it!