|
|
01-05-2021, 08:13 PM | #1 |
Senior Member
Join Date: Mar 2002
Location: Warsaw, Mo
Posts: 702
Likes: 612
Liked 1,097 Times in 345 Posts
|
1.3 Rocker Arms for Cam break in
I am thinking about buying a set of 1.3 Rocker arms to break the Cam in on my I/S Camaro. My question is would you need shorter push rods to do this or would the stock length work. Would make it easier then changing valve springs.
Randy Wells I/S 5628 |
01-05-2021, 09:49 PM | #2 |
Member
Join Date: Mar 2012
Posts: 239
Likes: 3
Liked 80 Times in 47 Posts
|
Re: 1.3 Rocker Arms for Cam break in
do racers still do the light ratio rockers / light springs these days ?. prefillng the carb with fuel / setting about 10 degrees advance timing and loading up the crankcase with a good brand of breakin oil with lots of phosphorus and zinc in the blend ( check the label if those ingredients on the bottle label ) a quick crank / firing up to a good high break in rpm should be all you need ... maybe I.m old school on this method
|
Liked |
01-05-2021, 10:36 PM | #3 |
Member
Join Date: Nov 2016
Location: Indianola Washington
Posts: 370
Likes: 0
Liked 426 Times in 134 Posts
|
Re: 1.3 Rocker Arms for Cam break in
Several factors are involved here.
# 1 is what you cam/lifter manufacture tells you. Follow it. Some cam manufactures will say if you keep over the nose spring pressure under 300 lbs you SHOULD be fine. After break in, pretty easy and good insurance to inspect each lifter. Steve Teeter STK/SS 620 |
Liked |
01-05-2021, 10:44 PM | #4 | |
Senior Member
Join Date: Mar 2002
Location: Warsaw, Mo
Posts: 702
Likes: 612
Liked 1,097 Times in 345 Posts
|
Re: 1.3 Rocker Arms for Cam break in
Quote:
Randy Wells I/S 5628 |
|
01-06-2021, 10:05 AM | #5 |
VIP Member
Join Date: Dec 2002
Location: Lower Dakota territory
Posts: 1,174
Likes: 1,044
Liked 777 Times in 232 Posts
|
Re: 1.3 Rocker Arms for Cam break in
I would recommend the light spring method for break in. There's more to it than just reducing the over-the-nose pressure. Changing springs is, at the worst, a minor inconvenience when you consider how critical proper break in is. -Al
__________________
"That'll never work....." |
Liked |
01-06-2021, 10:40 AM | #6 |
Member
Join Date: Dec 2005
Posts: 250
Likes: 294
Liked 130 Times in 25 Posts
|
Re: 1.3 Rocker Arms for Cam break in
I would break cam in with ceramic lifters and the swap them out after warm-up and 3-4 pulls on the dyno.
|
01-05-2021, 10:54 PM | #7 |
VIP Member
Join Date: Aug 2013
Posts: 1,766
Likes: 1,197
Liked 1,958 Times in 493 Posts
|
Re: 1.3 Rocker Arms for Cam break in
First time I swapped springs, huge pain. I bought 1.3 ratio rockers, way easier. The only issue I had was the pushrods hit the head where they pass through, had to really open up the hole up.
__________________
Todd Greene |
Liked |
01-05-2021, 11:01 PM | #8 | |
Senior Member
Join Date: Mar 2002
Location: Warsaw, Mo
Posts: 702
Likes: 612
Liked 1,097 Times in 345 Posts
|
Re: 1.3 Rocker Arms for Cam break in
Quote:
Randy Wells |
|
|
|