Ford vs Chevy Build-up - Page 27

Chris1529 · 03-10-2015, 09:28 PM

I think that hole was used for some sort of an emissions tube on some vehicles.

I would go with the 2.92 first gear.

My car worked very well with 26" tires. I am thinking of going back to them.

You will have no problems.

Your car is looking great.

HandOverFist · 03-11-2015, 01:07 AM

I figure I will be down on hp just like our other car lol. Couple that with the weight I doubt I will have much issue with tire spin hehe.

HandOverFist · 03-12-2015, 02:40 AM

Some trial fitting of components shows slight interference between the fuel rails and lower manifold...just a touch with the die grinder will remedy that. As I suspected the rockers will need just a tad more clearance with the stock valve covers...I can either double gasket them or run an aftermarket set I have on hand. The tall covers present even more problems with interference on the upper plenum not to mention the inability to remove either cover without pulling the upper plenum first. I'm thinking stick to the factory pieces.

Tony Corley · 03-12-2015, 04:37 PM

Keep the factory pieces and clearance the inside of the valve cover. Parts are on the way.

Tony Corley · 03-12-2015, 04:42 PM

Did you paint or powder coat the valve covers and intake?

HandOverFist · 03-13-2015, 12:56 AM

Just some leftover paint I had from the trunk.

HandOverFist · 03-13-2015, 03:32 PM

Due to looming time constraints and the seemingly lack of C4 cores I bought a race ready C4 from Dynamic Transmission in Conn. It will be a fwd manual valve body, rollerized and equipped with a 2.90 gearset.

Had I known it was going to be such a problem locating a core I would have began my search much earlier. When Arnett told me he had not located one I knew I was in trouble. I'll still get Thomas to build one if a core ever materializes for a spare. All I need now is to get a convertor spec'd by ATI or someone else.

SSGT Mustang · 03-13-2015, 07:04 PM

I probably should have mentioned this earlier, but I didn't know that you were in the market for a built C4 instead of just a core.

Ed Horensky who I believe is a member of this site is very, very knowledgable about C4's. I highly recommend that you look him up.

I sent the C4 in my Super Stocker to Dynamic for a rebuild. They did a very nice job, and seemed to have worked out some longstanding problems that I had with the trans brake. They are a good shop, and I'm sure that you'll be happy with them. I still would strongly recommend that you talk to Ed. He has information about many things that will be helpful to you.

I used JPT converters for a long time, but switched to Coan when Jim retired. I'm very pleased with Coan for many reasons. Excellent shop.

Several guys I know switched from other converter builders to Ultimate and picked up. You may want to give them a call, or Coan.

Nothing against ATI, but they would not be my first choice for a C4.

HandOverFist · 03-13-2015, 07:18 PM

I wasnt in the market for a built trans until recently when I realized a waiting on a suitable core was going to seriously put me behind. I would be interested in other's experiences with different convertors...this is not set in concrete yet.

partsbob67 · 03-13-2015, 08:30 PM

is that spacer legal between the manifold halves?

03-10-2015, 09:28 PM	#261
Chris1529 VIP Member Join Date: Dec 2006 Location: West Virginia Posts: 1,366 Likes: 6 Liked 70 Times in 29 Posts	Re: Ford vs Chevy Build-up I think that hole was used for some sort of an emissions tube on some vehicles. I would go with the 2.92 first gear. My car worked very well with 26" tires. I am thinking of going back to them. You will have no problems. Your car is looking great. __________________ Chris Bowman The Mountain State Mustang 1984 Mustang GT350

03-11-2015, 01:07 AM	#262
HandOverFist VIP Member Join Date: Oct 2013 Location: Gulf Breeze, FL Posts: 1,651 Likes: 8 Liked 33 Times in 16 Posts	Re: Ford vs Chevy Build-up I figure I will be down on hp just like our other car lol. Couple that with the weight I doubt I will have much issue with tire spin hehe. __________________ Rich Taylor I/SA - 321

03-12-2015, 02:40 AM	#263
HandOverFist VIP Member Join Date: Oct 2013 Location: Gulf Breeze, FL Posts: 1,651 Likes: 8 Liked 33 Times in 16 Posts	Re: Ford vs Chevy Build-up Some trial fitting of components shows slight interference between the fuel rails and lower manifold...just a touch with the die grinder will remedy that. As I suspected the rockers will need just a tad more clearance with the stock valve covers...I can either double gasket them or run an aftermarket set I have on hand. The tall covers present even more problems with interference on the upper plenum not to mention the inability to remove either cover without pulling the upper plenum first. I'm thinking stick to the factory pieces. __________________ Rich Taylor I/SA - 321

03-12-2015, 04:37 PM	#264
Tony Corley Member Join Date: Nov 2011 Posts: 264 Likes: 42 Liked 61 Times in 25 Posts	Re: Ford vs Chevy Build-up Keep the factory pieces and clearance the inside of the valve cover. Parts are on the way.

03-12-2015, 04:42 PM	#265
Tony Corley Member Join Date: Nov 2011 Posts: 264 Likes: 42 Liked 61 Times in 25 Posts	Re: Ford vs Chevy Build-up Did you paint or powder coat the valve covers and intake? Last edited by Tony Corley; 03-13-2015 at 06:00 AM.

03-13-2015, 12:56 AM	#266
HandOverFist VIP Member Join Date: Oct 2013 Location: Gulf Breeze, FL Posts: 1,651 Likes: 8 Liked 33 Times in 16 Posts	Re: Ford vs Chevy Build-up Just some leftover paint I had from the trunk. __________________ Rich Taylor I/SA - 321

03-13-2015, 03:32 PM	#267
HandOverFist VIP Member Join Date: Oct 2013 Location: Gulf Breeze, FL Posts: 1,651 Likes: 8 Liked 33 Times in 16 Posts	Re: Ford vs Chevy Build-up Due to looming time constraints and the seemingly lack of C4 cores I bought a race ready C4 from Dynamic Transmission in Conn. It will be a fwd manual valve body, rollerized and equipped with a 2.90 gearset. Had I known it was going to be such a problem locating a core I would have began my search much earlier. When Arnett told me he had not located one I knew I was in trouble. I'll still get Thomas to build one if a core ever materializes for a spare. All I need now is to get a convertor spec'd by ATI or someone else. __________________ Rich Taylor I/SA - 321

03-13-2015, 07:04 PM	#268
SSGT Mustang Member Join Date: Mar 2005 Location: Jersey Posts: 359 Likes: 35 Liked 204 Times in 54 Posts	Re: Ford vs Chevy Build-up I probably should have mentioned this earlier, but I didn't know that you were in the market for a built C4 instead of just a core. Ed Horensky who I believe is a member of this site is very, very knowledgable about C4's. I highly recommend that you look him up. I sent the C4 in my Super Stocker to Dynamic for a rebuild. They did a very nice job, and seemed to have worked out some longstanding problems that I had with the trans brake. They are a good shop, and I'm sure that you'll be happy with them. I still would strongly recommend that you talk to Ed. He has information about many things that will be helpful to you. I used JPT converters for a long time, but switched to Coan when Jim retired. I'm very pleased with Coan for many reasons. Excellent shop. Several guys I know switched from other converter builders to Ultimate and picked up. You may want to give them a call, or Coan. Nothing against ATI, but they would not be my first choice for a C4.

03-13-2015, 07:18 PM	#269
HandOverFist VIP Member Join Date: Oct 2013 Location: Gulf Breeze, FL Posts: 1,651 Likes: 8 Liked 33 Times in 16 Posts	Re: Ford vs Chevy Build-up I wasnt in the market for a built trans until recently when I realized a waiting on a suitable core was going to seriously put me behind. I would be interested in other's experiences with different convertors...this is not set in concrete yet. __________________ Rich Taylor I/SA - 321

03-13-2015, 08:30 PM	#270
partsbob67 Member Join Date: Apr 2005 Location: rohnert park,ca Posts: 414 Likes: 11 Liked 79 Times in 11 Posts	Re: Ford vs Chevy Build-up is that spacer legal between the manifold halves? __________________ bob beals 7244