Woodfin's SS GT/TB construction series

Little Chief · 11-01-2014, 07:30 PM

Amen brother, I find if it's installed and removed 3 or 4 times I can generally live with it.

Dragsinger · 11-01-2014, 08:33 PM

Little Chief, lets us become one with the machine.

Bench Racer · 11-02-2014, 04:04 AM

Larry, I don't think that ignition system will pass through the barn at Indy, you have to use points when the distributor is driven off the pushrods.

Dragsinger · 11-02-2014, 05:41 AM

Bench,

My lobby machine is working with NHRA to amend the "must use points with pushrod drive" ruling.

I expect to succeed because they have already allowed running double valve cover gaskets.

Dragsinger · 11-02-2014, 08:18 PM

Sunday afternoon progress.

As posted earlier I decided to buy the roll cage kit from Auto Weld Chassis. My first impression is very good. All tubing is labeled and all cuts de-burred.

This photo in just off the FedEx truck and un-wrapped.

Dragsinger · 11-02-2014, 08:28 PM

Auto Weld Chassis tubing kit

Dragsinger · 11-02-2014, 08:30 PM

A donor truck is providing the interior.

Dragsinger · 11-02-2014, 09:09 PM

More about the Auto Weld Chassis roll cage kit.

This series of photos shows an initial fitting of the mail hoop. It is designed to go through the floor and set directly on the rear cab mount. The cab mount is re-located inside the frame.

The main hoop is intentionally cut slightly long to allow just the fit you want. The photos show it slipped through the floor and touching the cab mount [factory cab mount is removed]

The legs are too long as seen by the bar touch the cab mount at an angle. Once the legs are the correct length they will set squarely on the mounts. I will take several small cuts off the hoop legs to sneak up on the fit I want. Even will put the drivers seat in position to check fit.

A plate welds to cab mounts and hoop legs. In addition, the mount will be braced. In side the cab, two "struts" come off the hoop legs down to the floor.

Dragsinger · 11-02-2014, 09:16 PM

the 12 bolt Chevy housing awaits Strange axles, spool, and gear set. Notice the Strange aluminum caps yet to be fitted to housing.

The housing is not cut to length, you can just make out a chalk double arrow showing the left side cut.

Mittler Brothers pinion center gauge and housing narrowing kit is ready for service,

More soon,

ConstructionFin

Little Chief · 11-02-2014, 10:57 PM

Larry, I can see everything coming together now.

11-01-2014, 07:30 PM	#1
Little Chief Junior Member Join Date: Sep 2014 Location: Liberty City, Texas Posts: 31 Likes: 0 Liked 0 Times in 0 Posts	Re: Woodfin's SS GT/TB construction series Amen brother, I find if it's installed and removed 3 or 4 times I can generally live with it.

11-01-2014, 08:33 PM	#2
Dragsinger VIP Member Join Date: Jul 2008 Location: Liberty City [East Texas] Posts: 1,760 Likes: 5 Liked 99 Times in 60 Posts	Re: Woodfin's SS GT/TB construction series Little Chief, lets us become one with the machine. __________________ Larry Woodfin 471W

11-02-2014, 04:04 AM	#3
Bench Racer Member Join Date: May 2002 Location: Green Creek (Tryon) North Carolina Posts: 331 Likes: 69 Liked 99 Times in 21 Posts	Re: Woodfin's SS GT/TB construction series Larry, I don't think that ignition system will pass through the barn at Indy, you have to use points when the distributor is driven off the pushrods.

11-02-2014, 05:41 AM	#4
Dragsinger VIP Member Join Date: Jul 2008 Location: Liberty City [East Texas] Posts: 1,760 Likes: 5 Liked 99 Times in 60 Posts	Re: Woodfin's SS GT/TB construction series Bench, My lobby machine is working with NHRA to amend the "must use points with pushrod drive" ruling. I expect to succeed because they have already allowed running double valve cover gaskets. __________________ Larry Woodfin 471W

11-02-2014, 08:18 PM	#5
Dragsinger VIP Member Join Date: Jul 2008 Location: Liberty City [East Texas] Posts: 1,760 Likes: 5 Liked 99 Times in 60 Posts	Re: Woodfin's SS GT/TB construction series Sunday afternoon progress. As posted earlier I decided to buy the roll cage kit from Auto Weld Chassis. My first impression is very good. All tubing is labeled and all cuts de-burred. This photo in just off the FedEx truck and un-wrapped. __________________ Larry Woodfin 471W

11-02-2014, 08:28 PM	#6
Dragsinger VIP Member Join Date: Jul 2008 Location: Liberty City [East Texas] Posts: 1,760 Likes: 5 Liked 99 Times in 60 Posts	Re: Woodfin's SS GT/TB construction series Auto Weld Chassis tubing kit Attached Thumbnails __________________ Larry Woodfin 471W

11-02-2014, 08:30 PM	#7
Dragsinger VIP Member Join Date: Jul 2008 Location: Liberty City [East Texas] Posts: 1,760 Likes: 5 Liked 99 Times in 60 Posts	Re: Woodfin's SS GT/TB construction series A donor truck is providing the interior. Attached Thumbnails __________________ Larry Woodfin 471W

11-02-2014, 09:09 PM	#8
Dragsinger VIP Member Join Date: Jul 2008 Location: Liberty City [East Texas] Posts: 1,760 Likes: 5 Liked 99 Times in 60 Posts	Re: Woodfin's SS GT/TB construction series More about the Auto Weld Chassis roll cage kit. This series of photos shows an initial fitting of the mail hoop. It is designed to go through the floor and set directly on the rear cab mount. The cab mount is re-located inside the frame. The main hoop is intentionally cut slightly long to allow just the fit you want. The photos show it slipped through the floor and touching the cab mount [factory cab mount is removed] The legs are too long as seen by the bar touch the cab mount at an angle. Once the legs are the correct length they will set squarely on the mounts. I will take several small cuts off the hoop legs to sneak up on the fit I want. Even will put the drivers seat in position to check fit. A plate welds to cab mounts and hoop legs. In addition, the mount will be braced. In side the cab, two "struts" come off the hoop legs down to the floor. Attached Thumbnails __________________ Larry Woodfin 471W

11-02-2014, 09:16 PM	#9
Dragsinger VIP Member Join Date: Jul 2008 Location: Liberty City [East Texas] Posts: 1,760 Likes: 5 Liked 99 Times in 60 Posts	Re: Woodfin's SS GT/TB construction series the 12 bolt Chevy housing awaits Strange axles, spool, and gear set. Notice the Strange aluminum caps yet to be fitted to housing. The housing is not cut to length, you can just make out a chalk double arrow showing the left side cut. Mittler Brothers pinion center gauge and housing narrowing kit is ready for service, More soon, ConstructionFin Attached Thumbnails __________________ Larry Woodfin 471W

11-02-2014, 10:57 PM	#10
Little Chief Junior Member Join Date: Sep 2014 Location: Liberty City, Texas Posts: 31 Likes: 0 Liked 0 Times in 0 Posts	Re: Woodfin's SS GT/TB construction series Larry, I can see everything coming together now.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode