|
|
|
|
04-23-2018, 06:13 PM
|
#1 |
|
Junior Member
Join Date: Sep 2012
Posts: 98
Likes: 20
Liked 32 Times in 13 Posts
|
Re: Mounting Turbo Action Shifter
Mine is mounted on a pedestal on the tunnel bringing the shifter up an closer to me.
|
|
|
|
04-23-2018, 06:29 PM
|
#2 | |
|
VIP Member
Join Date: Oct 2007
Posts: 1,168
Likes: 487
Liked 346 Times in 126 Posts
|
Re: Mounting Turbo Action Shifter
Quote:
Thanks to all for the help |
|
|
|
|
|
04-24-2018, 03:52 PM
|
#3 |
|
Member
Join Date: May 2010
Location: El Dorado Ca.
Posts: 123
Likes: 299
Liked 49 Times in 22 Posts
|
Re: Mounting Turbo Action Shifter
I use a piece of angle iron, so its sits up higher, and i weld the angle to the floor, with some flat bar on the other side for support, then bolt the shifter to angle.
__________________
Steven Barnes Stock 704 N/SA |
|
|
|
|
04-26-2018, 02:34 AM
|
#4 |
|
VIP Member
Join Date: Jun 2009
Location: Boulder City, Nevada 89005
Posts: 2,739
Likes: 2,824
Liked 2,493 Times in 700 Posts
|
Re: Mounting Turbo Action Shifter
We do our like Rick said in our A Body stuff.
Round tubing with plates on both sides that brings it up a foot to foot and half above floor. I can E Mail you pics if you like. Mine is just a couple inches from the wheel so to reduce movement after leaving line. Of course......I am old and move slowly!
__________________
John Irving 741 Stock 741 Super Stock |
|
|
|
|
04-26-2018, 09:27 AM
|
#5 |
|
Member
Join Date: Jun 2010
Location: VA
Posts: 230
Likes: 24
Liked 21 Times in 13 Posts
|
Re: Mounting Turbo Action Shifter
John, I'd like to see that picture, thanks. I'll PM my email
Brian
__________________
Brian Carpenter Stock 1358 |
|
|
|
|
04-26-2018, 03:23 PM
|
#6 |
|
VIP Member
Join Date: Jun 2009
Location: Boulder City, Nevada 89005
Posts: 2,739
Likes: 2,824
Liked 2,493 Times in 700 Posts
|
Re: Mounting Turbo Action Shifter
I will take pics as soon as I am back from Muscle cars at Strip
Stock/Super Stock on Monday.
__________________
John Irving 741 Stock 741 Super Stock |
|
|
|
|
04-27-2018, 11:46 AM
|
#7 |
|
VIP Member
Join Date: Nov 2001
Location: Florida
Posts: 1,542
Likes: 34
Liked 138 Times in 51 Posts
|
Re: Mounting Turbo Action Shifter
I have a Hurst 1/4 stick but made my floor bracket from a piece of channel iron about 2" wide and 1/2" tall, maybe 1/8" thick. (My local Home Depot sells lengths of it. Drilled it to match the shifter mounting pattern and bolted it together with short 1/4" bolts.Nuts were then welded underneath to stay in place when shifter is removed. Then the channel piece was welded to the floor/tunnel in a comfortable location.
__________________
LOCOMOTION Racing Last edited by Myron Piatek; 04-27-2018 at 11:50 AM. |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
