96 Mustang FGT/G

[GHoef]

Could you also run SS/FM ? (10.50 index @ 12.50 lbs per C.I.) No tear downs and weight looks the same. 302 cid × 12.50 lb = 3400- ish lb min. Same as your 9.0 x 380hp = 3420 lbs.

[FireSale]

Originally Posted by GHoef

Could you also run SS/FM ? (10.50 index @ 12.50 lbs per C.I.) No tear downs and weight looks the same. 302 cid × 12.50 lb = 3400- ish lb min. Same as your 9.0 x 380hp = 3420 lbs.

That's a fuel injected engine, so no. /FM is carburetor canted or inline valves. I think it's a Coyote, can't find a Cobra Jet for 2011.

[George Wright]

It is a 2012 CobraJet 5 Liter naturally aspirated engine, not a 2011. This engine is rated 325 OEM / 300 NHRA, not 380. The 2013 and 2014 are rated higher since they have the large Acufab throttle body. My combo has the small OEM throttle body.
As for SS/FM this engine has EFI and 4 four valves per cylinder, both not allowed in modified. However the rule book does not specifically say "no overhead cams". The Coyote has 4 overhead cams and 32 valves.

I will just continue to run Super Stock where I can adhear to my strict "NO CARB" diet.

[BRETV]

Factory K member? What did you have to modify? Thanks








Bret Velde
2003 ??

[George Wright]

Originally Posted by BRETV

Factory K member? What did you have to modify? Thanks








Bret Velde
2003 ??

Both this car and my 82 Mustang which also has a Coyote engine have factory K members. The middle cross member was cut out and replaced with tubing on each car. I also had to clearance the k-members in some areas. I will search through my photos and see if I have any pictures of the K members. Once the engine is in, it is very difficult to see the K member from the top. I did my 82 mustang back in 2011 and had to build my own headers. When I did the 96 Mustang we got a set of American Racing Headers. I believe that the American Racing Headers were designed for an after market tubular K member, but I was able to fit them on the 96. The only modification I need to do was to redo the bend that went over the starter pocket on the cylinder 1 tube. This tube would fit a stick shift bell housing or a stock c4 case, but I have an SFI C4 bell housing on the 96 that is very thick.



Here is a picture of my 82 Mustang GT that also has a 5.0 Coyote. I am in the process of putting a G-Force clutch-less 5 speed in the 82. I have plans for one of our guys to race the 82 at some NHRA opens or points meets later this year.



This photo was taken at a CobraJet test session at Milan Dragway back in late 2012.

[BRETV]

Originally Posted by George Wright

Both this car and my 82 Mustang which also has a Coyote engine have factory K members. The middle cross member was cut out and replaced with tubing on each car. I also had to clearance the k-members in some areas. I will search through my photos and see if I have any pictures of the K members. Once the engine is in, it is very difficult to see the K member from the top. I did my 82 mustang back in 2011 and had to build my own headers. When I did the 96 Mustang we got a set of American Racing Headers. I believe that the American Racing Headers were designed for an after market tubular K member, but I was able to fit them on the 96. The only modification I need to do was to redo the bend that went over the starter pocket on the cylinder 1 tube. This tube would fit a stick shift bell housing or a stock c4 case, but I have an SFI C4 bell housing on the 96 that is very thick.



Here is a picture of my 82 Mustang GT that also has a 5.0 Coyote. I am in the process of putting a G-Force clutch-less 5 speed in the 82. I have plans for one of our guys to race the 82 at some NHRA opens or points meets later this year.



This photo was taken at a CobraJet test session at Milan Dragway back in late 2012.

Thanks George for the explanation and the pics.

[ALMACK]

Looks good George.

How did you mate the cogged water pump pulley to the 5.0 Coyote water pump ?

Did you have to machine an adaptor ?

[GHoef]

Good to know, still learning. The car is awesome btw