|
|
|
|
04-23-2021, 09:16 AM
|
#1 |
|
Member
Join Date: Jul 2008
Location: Houston, Texas
Posts: 346
Likes: 906
Liked 359 Times in 140 Posts
|
Re: Dumbo The Flying Elephant
...
Last edited by 1matcoman; 04-23-2021 at 09:25 AM. |
|
|
|
04-26-2021, 01:21 PM
|
#2 |
|
VIP Member
Join Date: Feb 2014
Location: Derby City, USA
Posts: 3,663
Likes: 1,094
Liked 8,218 Times in 1,537 Posts
|
Re: Dumbo The Flying Elephant
eezrvproducts.com. ........this tire pressure system monitors the pressure and temp of tires. I have used it for a few years and highly recommend it.....
|
|
|
|
|
04-26-2021, 02:33 PM
|
#3 |
|
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,677
Likes: 1,992
Liked 10,969 Times in 2,261 Posts
|
Re: Dumbo The Flying Elephant
^^^^^^^^^^^^^^^That's the one we use^^^^^^^^^^^^
|
|
|
|
|
04-28-2021, 09:01 AM
|
#4 |
|
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,677
Likes: 1,992
Liked 10,969 Times in 2,261 Posts
|
Re: Dumbo The Flying Elephant
To my surprise the largest, most pages, section of my notes is the suspension section on the four wheel scales.
|
|
|
|
| Liked |
|
04-30-2021, 07:18 AM
|
#5 |
|
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,677
Likes: 1,992
Liked 10,969 Times in 2,261 Posts
|
Re: Dumbo The Flying Elephant
For me the biggest question during dissemble is why? Why is there more ware on this side and not the other. After noticing change comes the questions; does it need fixing and if it does how?
Off topic but we are updating our gages in the Cuda to Classic Instruments 40* to 220* water, oil, and trans temp, plus the oil pressure gages. |
|
|
|
| Liked |
|
05-02-2021, 06:43 PM
|
#6 |
|
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,677
Likes: 1,992
Liked 10,969 Times in 2,261 Posts
|
Re: Dumbo The Flying Elephant
I removed a piston and rod. Checked the stretch of the rod bolts and the bolts matched the information on my build sheet. When relaxed the numbers agreed again. No sign of cap fretting or back side of bearing insert micro welding itself to the rod. Rings seemed to take to piston and cylinder wall. Top two rings were separated by about 120*, the oil rails were lined up over each other. Was that the reason the top of piston had a little extra carbon build up?
It will be good to know how round and straight the cylinder walls stayed. Our toy airplane engines ran well when they were round and straight. |
|
|
|
| Liked |
|
05-09-2021, 06:15 PM
|
#7 |
|
Live Reporter
Join Date: Oct 2004
Location: Hickory, Ky
Posts: 10,677
Likes: 1,992
Liked 10,969 Times in 2,261 Posts
|
Re: Dumbo The Flying Elephant
Selling the Private Lee has been way more time consuming than thought. I'm still finding parts.
I'm sending off a couple of test valves to be coated, I sure hope it will extend the service life of stuff. |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
