|
04-07-2014, 10:05 AM | #11 |
Member
Join Date: Mar 2009
Location: Hampstead, MD.
Posts: 426
Likes: 287
Liked 65 Times in 23 Posts
|
Re: Stainless Steel Headers... worth it or no?
I put a set of REF headers on my car just yesterday. They fit like a glove. The quality is great also. After years of fighting my old Hookers these REF's were a dream to install. Everyone I've talked to say they make good power too. I highly recommend them and have them coated.
__________________
Jody Aberts Troublemaker2 1966 Fairlane 427 |
04-07-2014, 10:23 AM | #12 | |
VIP Member
Join Date: Jan 2005
Location: Where the Green Grass Grows, AL
Posts: 2,375
Likes: 0
Liked 3 Times in 3 Posts
|
Re: Stainless Steel Headers... worth it or no?
Quote:
__________________
Chad Rhodes 2113 I/SA |
|
04-07-2014, 10:26 AM | #13 |
Senior Member
Join Date: Dec 2001
Location: NY, NY
Posts: 742
Likes: 170
Liked 182 Times in 42 Posts
|
Re: Stainless Steel Headers... worth it or no?
Any thoughts about coating on a stainless header?
would there be any advantage there... other than that you would have to worry about the headers rusting from the inside out?
__________________
Angelo DiTocco '98 Firebird SS/HA '98 Firebird B/SA |
04-07-2014, 11:49 AM | #14 |
Senior Member
Join Date: Mar 2002
Location: Woodburn, Or
Posts: 640
Likes: 73
Liked 709 Times in 213 Posts
|
Re: Stainless Steel Headers... worth it or no?
I've built lots of both ms & ss headers. In spite of price, ss is definitely the way to go, virtually indestructible. Having run both ss and ms headers on my own car, I can tell you that they hold heat way longer than ms, you can't get anywhere near them even 20 minutes after coming back from a run. Regarding tri Y's, don't consider them unless you are willing to commit the time to tuning things in, they are very unforgiving if you miss on the combination. In an ideal world, I would recommend ss headers and having them coated to at least keep the under hood heat radiation under control. The other negative to ss (besides the cost) is that the tubing tends to be 16 ga and that makes the overall weight higher, I have always prefered to use 18 ga on race headers just to keep the weight down. If money is really not an issue, consider the Nascar tri Y paper thin Inconell version, can't even imagine what those cost.
Jim Caughlin SS 6019 |
04-07-2014, 11:58 AM | #15 |
Member
Join Date: Oct 2002
Location: Magnolia, Texas
Posts: 404
Likes: 1
Liked 461 Times in 61 Posts
|
Re: Stainless Steel Headers... worth it or no?
Approx $9000+/-
But they can be very brittle. My Elston Stainless both sides together weighed less than one side of our old Heddman headers. Last edited by Bill Grubbs; 04-07-2014 at 12:06 PM. |
04-07-2014, 09:15 PM | #16 |
Senior Member
Join Date: Nov 2007
Posts: 615
Likes: 56
Liked 166 Times in 59 Posts
|
Re: Stainless Steel Headers... worth it or no?
I have been build headers for several years now ,steel and stainless , I always suggest the stainless ,, you don't have to coat them and no rust issues will offset how often you will have to coat steel and rust will build up in steel no matter the company who does them ,, also if your building new engines and dynoing them with coated ones you will burn the coating off the top bends , but ceramic coated headers do offer the heat being contained in side the tube ,, stainless doesn't offer any heat barrier , if your r&d ing with header sizes a lot then steel is the way to go gmonde
www.gmondeperformance.com |
04-08-2014, 05:23 AM | #17 |
Senior Member
Join Date: Dec 2002
Location: Lincoln, Nebraska
Posts: 785
Likes: 45
Liked 318 Times in 67 Posts
|
Re: Stainless Steel Headers... worth it or no?
I talked with Kromer a few years ago and he needed the car on premises...do others mentioned here (Lelchook, REF, Elston etc) have that same requirement?
Kromer also requested spec sheet on port design, flow, etc.....others? Thanks in advance for any opinions I run my 1995 Jack Davis headers, it sounds like I may be giving something up, they are looking kind of rough |
04-08-2014, 06:20 AM | #18 |
Member
Join Date: Sep 2006
Location: Genoa, Illinois
Posts: 488
Likes: 9
Liked 6 Times in 4 Posts
|
Re: Stainless Steel Headers... worth it or no?
gmonde... Your site link shows a virus. My AVG caught it...
|
04-08-2014, 01:24 PM | #19 |
Junior Member
Join Date: Mar 2003
Location: Detroit,MI
Posts: 77
Likes: 25
Liked 27 Times in 13 Posts
|
Re: Stainless Steel Headers... worth it or no?
I worked with Kromerkraft from about 1995 to roughly 2005. I'm guessing we built 1 set of stainless for every 80-100 sets of mild steel headers during that period. A good ceramic coating will last several years. I can't remember any customers complaining about rust during this period. We never recommended SS during that period of time. After the first set, we tried to talk the handfull of customers out of SS.
And yes, he likes having the car on site to fit the headers. They are custom fit. We had a fixture for Gary Russell LT1 F-bodies in that time. Gary sents numerous customers to us. We never had a customer do a back to back test,....so I don;t know if there is a perf. benefit. Generally the Tri-Y's help the mid range and peak torque and lose a little max power. (based my experience and it varies from car to car if there is a benefit). Thanks, Ron |
04-09-2014, 04:15 PM | #20 | |
VIP Member
Join Date: Apr 2003
Location: Tulsa, Oklahoma
Posts: 1,609
Likes: 3,483
Liked 704 Times in 305 Posts
|
Re: Stainless Steel Headers... worth it or no?
Quote:
Bill |
|
|
|