|
![]() |
#341 |
Member
Join Date: Dec 2015
Location: TUCSON , AZ.
Posts: 168
Likes: 10
Liked 0 Times in 0 Posts
|
![]()
Todd , that was funny .... the reason I did it was I just to lazy to figure out what I needed..... Not because they are stainless .....hahaha
__________________
Old Nick in Tucson! Hahaha |
![]() |
![]() |
![]() |
#342 |
VIP Member
Join Date: Aug 2013
Posts: 1,763
Likes: 1,197
Liked 1,955 Times in 492 Posts
|
![]()
Here are the seat brackets cut and tacked in for fitting.
![]() ![]()
__________________
Todd Greene |
![]() |
![]() |
![]() |
#343 |
VIP Member
Join Date: Oct 2007
Posts: 1,168
Likes: 487
Liked 346 Times in 126 Posts
|
![]()
you are not going to powdercoat the seats?
|
![]() |
![]() |
![]() |
#344 |
VIP Member
Join Date: Aug 2013
Posts: 1,763
Likes: 1,197
Liked 1,955 Times in 492 Posts
|
![]()
After they've been fitted and welded LOL.
__________________
Todd Greene |
![]() |
![]() |
![]() |
#345 |
VIP Member
Join Date: Aug 2013
Posts: 1,763
Likes: 1,197
Liked 1,955 Times in 492 Posts
|
![]()
More black emblems, new door strikers
![]() ![]() ![]()
__________________
Todd Greene Last edited by Nmbr1GMfan; 05-26-2018 at 07:40 PM. |
![]() |
![]() |
![]() |
#346 |
VIP Member
Join Date: Aug 2013
Posts: 1,763
Likes: 1,197
Liked 1,955 Times in 492 Posts
|
![]()
YES! Got my helper back this weekend.
![]() ![]()
__________________
Todd Greene |
![]() |
![]() |
![]() |
#347 |
VIP Member
Join Date: Aug 2013
Posts: 1,763
Likes: 1,197
Liked 1,955 Times in 492 Posts
|
![]()
Finally making seat progress.
![]() ![]() ![]()
__________________
Todd Greene |
![]() |
![]() |
![]() |
#348 |
VIP Member
Join Date: Aug 2013
Posts: 1,763
Likes: 1,197
Liked 1,955 Times in 492 Posts
|
![]()
So, I don't know how ya'll do carpet around these bars but the last one I did was a butcher job, I wasn't happy with it so I knew I had to come up with something. now I'm pretty sure a sharp edge and nailing it with a hammer would do... but I like fire. My pipe could have been sharper but I heat it with a torch and shoved it right through the carpet, nice thing about this is, it's cauterized so it won't fray. Just a bit more to do and the carpet's done. I bought a carpet set plus 2yd of 80/20 for the rear section.
(First photo I didn't have the pipe hot enough on the first shot of my test pass, second one went right through). ![]() ![]() ![]() ![]() ![]()
__________________
Todd Greene |
![]() |
![]() |
![]() |
#349 |
VIP Member
Join Date: Dec 2002
Location: Lower Dakota territory
Posts: 1,180
Likes: 1,074
Liked 799 Times in 236 Posts
|
![]()
Hey...slick tip on the hot pipe. I've sharpened a frost plug and used a hammer but always had the fuzzies.
![]()
__________________
"That'll never work....." |
![]() |
![]() |
![]() |
#350 |
VIP Member
Join Date: Aug 2013
Posts: 1,763
Likes: 1,197
Liked 1,955 Times in 492 Posts
|
![]()
It worked beautifully, just wrap the pipe in a rag as it gets hot. I think I'll wrap 6" of it with some left over exhaust wrap.
__________________
Todd Greene |
![]() |
![]() |
![]() |
|
|