|
|
05-29-2016, 06:03 PM | #1 |
Member
Join Date: Jan 2004
Location: Belmont N.S. Canada
Posts: 452
Likes: 211
Liked 142 Times in 64 Posts
|
350/255HP Help please
Can anyone help me out a bit in knowing what my 350/255 stocker motor should be making for power and what rpm range it should be peaking at? I've been beating my head off the wall with this thing for a few years now and just dosen't want to get any better. I'm thinking I may have the wrong cam in it but really don't know where to turn next. Thanks.
__________________
Chris Chapman 1969 Chevelle NHRA F-G/SA 1090 |
05-29-2016, 08:26 PM | #2 |
VIP Member
Join Date: Dec 2002
Location: Lower Dakota territory
Posts: 1,166
Likes: 1,018
Liked 762 Times in 226 Posts
|
Re: 350/255HP Help please
Assuming no obvious issues, a couple of pulls on a dyno can save you lots of time.
What kind of h.p. numbers are you getting when calculating from the E.T.?
__________________
"That'll never work....." |
05-29-2016, 08:47 PM | #3 |
Member
Join Date: Jan 2004
Location: Belmont N.S. Canada
Posts: 452
Likes: 211
Liked 142 Times in 64 Posts
|
Re: 350/255HP Help please
Made 387 @ 5600 on A&J dyno. 100% new engine except for the cam as it was like new and only a couple seasons old. The worn out peice I had before made 384. The slide calculator agrees with this. A little background info, it's got all what's supposed to be great gear, .065 over cp c6 Pistons with total seal advantage ring pack, Manley rods, new heads from reputable shop that flow quite well, pac 1409x springs, bullet cam, short travel lifters etc.eal down is 8-9% cold, we've had it apart again to make sure nothing is going away or getting tight and all is well. It's just not adding up, and it's beginning to make my head hurt lol.
__________________
Chris Chapman 1969 Chevelle NHRA F-G/SA 1090 |
05-29-2016, 08:55 PM | #4 |
Senior Member
Join Date: Oct 2002
Location: Pittsburgh
Posts: 521
Likes: 246
Liked 550 Times in 106 Posts
|
Re: 350/255HP Help please
Are you saying the leakdown is 8 to 9%????
|
05-29-2016, 09:19 PM | #5 |
Member
Join Date: Dec 2014
Location: Perry, GA
Posts: 329
Likes: 11
Liked 236 Times in 89 Posts
|
Re: 350/255HP Help please
Not trying to be ugly but that combo should make north of 430. How "new" are pistons? Most likely the problem is the ring package. Having said that I am not an engine builder nor do I build my own motors but I have been around stock for all my life and fairly up to date with what it takes to make them run.
|
05-29-2016, 09:28 PM | #6 | |
Senior Member
Join Date: Feb 2012
Location: Colorado Springs Colorado/Thousand Oaks Ca
Posts: 606
Likes: 68
Liked 238 Times in 97 Posts
|
Re: 350/255HP Help please
Quote:
Last edited by HP HUNTER; 05-29-2016 at 09:32 PM. |
|
05-29-2016, 09:32 PM | #7 |
VIP Member
Join Date: May 2006
Location: Murfreesboro TN
Posts: 4,916
Likes: 997
Liked 1,046 Times in 276 Posts
|
Re: 350/255HP Help please
You're down 35HP or more, and your peak is maybe 600RPM or more low.
If you're really leaking close to 10% on an engine that is up to 160 degrees, you're not sealed up. I seriously doubt that either Total Seal or CP has missed the mark on the rings or pistons, especially if you had them work together. I've used their stuff successfully many times.
__________________
Alan Roehrich 212A G/S |
|
|