|
11-28-2016, 08:27 AM | #41 |
VIP Member
Join Date: Oct 2002
Location: On a hilltop in Pa.
Posts: 4,223
Likes: 3,103
Liked 6,791 Times in 1,524 Posts
|
Re: Mopar 273-4bbl Combo
It was and it should be gone.
__________________
Billy Nees 1188 STK, SS World's greatest Under-Achiever! |
11-28-2016, 09:37 AM | #42 |
VIP Member
Join Date: Oct 2002
Location: On a hilltop in Pa.
Posts: 4,223
Likes: 3,103
Liked 6,791 Times in 1,524 Posts
|
Re: Mopar 273-4bbl Combo
D-Darts had factory modified (intake openings bored out to accept Holley) standard 273 intakes. AND adapter plates.
__________________
Billy Nees 1188 STK, SS World's greatest Under-Achiever! |
11-30-2016, 07:10 PM | #43 |
Member
Join Date: May 2010
Location: El Dorado Ca.
Posts: 116
Likes: 243
Liked 34 Times in 20 Posts
|
Re: Mopar 273-4bbl Combo
I have found the early 64-66 blocks are better, i have a 65 block in my car, with some fill, all good so far, and i am just using the hooker headers for now, until i have Performance Welding build me a set someday.
__________________
Steven Barnes Stock 704 N/SA |
11-30-2016, 07:27 PM | #44 |
VIP Member
Join Date: Oct 2007
Posts: 1,097
Likes: 404
Liked 250 Times in 101 Posts
|
Re: Mopar 273-4bbl Combo
|
12-01-2016, 12:12 AM | #45 | |
VIP Member
Join Date: Feb 2003
Location: Glendale, Arizona
Posts: 2,991
Likes: 693
Liked 1,457 Times in 543 Posts
|
Re: Mopar 273-4bbl Combo
Quote:
It's a single plane cast iron intake with an adapter for the Holley carburetor. |
|
12-01-2016, 01:06 AM | #46 |
Member
Join Date: Aug 2010
Posts: 204
Likes: 2
Liked 57 Times in 23 Posts
|
Re: Mopar 273-4bbl Combo
hi, just curious, I seen marine intake for 318, casting number is2846707. the carb flange is angled quite a bit from level, thanks
|
12-01-2016, 01:26 AM | #47 |
Senior Member
Join Date: Jul 2014
Posts: 563
Likes: 34
Liked 47 Times in 32 Posts
|
Re: Mopar 273-4bbl Combo
The ones I've seen had angled spacers under carb, dad had two 400s with them. First boat had a ford 351 engine, angled spacer under carb.
|
12-01-2016, 08:24 AM | #48 |
VIP Member
Join Date: Oct 2002
Location: On a hilltop in Pa.
Posts: 4,223
Likes: 3,103
Liked 6,791 Times in 1,524 Posts
|
Re: Mopar 273-4bbl Combo
771 is also listed as 66 California.
__________________
Billy Nees 1188 STK, SS World's greatest Under-Achiever! |
12-01-2016, 02:41 PM | #49 |
VIP Member
Join Date: Feb 2003
Location: Glendale, Arizona
Posts: 2,991
Likes: 693
Liked 1,457 Times in 543 Posts
|
Re: Mopar 273-4bbl Combo
The LD4B Edelbrock intake was approved as a replacement for the 273 due to the fact it was available with a Chrysler part number. The same rationale used on the 440 Chrysler 6-Pack engine with the Edelbrock intake. The 6-Pack intake was available in both aluminum and cast iron.
|
12-01-2016, 03:47 PM | #50 | |
Senior Member
Join Date: Jul 2014
Posts: 563
Likes: 34
Liked 47 Times in 32 Posts
|
Re: Mopar 273-4bbl Combo
Quote:
|
|
Liked |
|
|