|
09-21-2014, 08:19 PM | #1 |
Member
Join Date: Oct 2008
Posts: 146
Likes: 2
Liked 40 Times in 6 Posts
|
Problem cutting a light
I have a 93 Formula f body firebird I run In D/PS.I am having trouble cutting a light with the car. I shallow stage, rpms at 1500 at start. I leave as the last yellow is starting to come on and the car gives me a .671 light. I made a second pass to make sure it wasn't me, it was another .6719. I have been fighting this all year. I have put air bags in the rear with 25psi in right rear, 5 in drivers. I have tried 35psi to 10 psi and no difference. Lower control arms are level with the frame ties. I have tried lowering them and it seems to hit tires harder. The torque arm is in the stock setting, but not mounted to the trans. Springs are v6 springs with a 1/2 coil cut off. The rear shocks are 50/50 new lakewood. Stock anti roll bar. I have 145#s of weight in the rear of the car to make weight. The converter is built for the car combination. I have 4.56 rear gears with 26x8.5 rear tires.
The front suspension has 6" of travel for the front tires to fall out of wheel well. Lakewood 90/10 shocks with stock springs on front with 1 coil cut off. I was thinking of making front end limiters so i could make the car move forward. In the car, it seems like the car is trying to rock back on the rear tires, while lifting the front. The 60ft times are great. Here are my times 1.608 60ft 8.10 1/8th 82.56 1/8th mph 12.82 1/4 102.89 1/4 mph I run 22 psi in the rear tires. The 60s are very consistent, and the car runs dead on the money every pass. Ran two 8.102 Saturday in tt and dialed in a 8.09. Ran 8.10 1st rd and lost because i had a .6719 light. I practice on a practice tree every night. I am very consistent on it in several different situations. I am going to lower the torque arm 1 1/4 inches in the front and see what happens. Is that the right move ? Also how many racers use front end limiters on there stockers? Is 6" to much travel? Was thinking of limiting to 4" and see what happens. I am looking to classracer for help. Thanks In advance. Last edited by russellauto1; 09-21-2014 at 08:32 PM. |
09-21-2014, 10:16 PM | #2 |
VIP Member
Join Date: Nov 2001
Location: Florida
Posts: 1,538
Likes: 34
Liked 132 Times in 48 Posts
|
Re: Problem cutting a light
It's a good sign if you're consistent. But is there another carb you could try? Could you have a carb "flat spot" that's not very obvious? Converter might be at least part of it, but that's still a lot to be "off".
__________________
LOCOMOTION Racing |
09-21-2014, 10:18 PM | #3 |
Member
Join Date: Oct 2008
Posts: 146
Likes: 2
Liked 40 Times in 6 Posts
|
Re: Problem cutting a light
It's a fuel injected car. It could possibly be converter. I ordered this one from mark yacovone . I have never tried another converter in it.
|
09-21-2014, 10:21 PM | #4 |
Senior Member
Join Date: Dec 2008
Location: Rainy Washington
Posts: 577
Likes: 4
Liked 129 Times in 49 Posts
|
Re: Problem cutting a light
Whats the launch rpm?
__________________
James Boyce 6052 K/SA Stock National record holder 2015,2018,2 times in 2022,2023 |
09-21-2014, 10:27 PM | #5 |
Member
Join Date: Oct 2008
Posts: 146
Likes: 2
Liked 40 Times in 6 Posts
|
Re: Problem cutting a light
Starting line rpms are 1500. I've tried 2000, but 60s slowed down and didn't seem to improve lights.
|
09-21-2014, 11:06 PM | #6 | |
VIP Member
Join Date: Nov 2001
Location: Florida
Posts: 1,538
Likes: 34
Liked 132 Times in 48 Posts
|
Re: Problem cutting a light
Quote:
Off hand, I can't imagine a converter affecting RT's that much. As an experiment, perhaps you can compare yourself to someone else in another car or practice tree to see how much of a variable you might be. Just trying to cover all the bases.
__________________
LOCOMOTION Racing Last edited by Myron Piatek; 09-21-2014 at 11:09 PM. |
|
09-21-2014, 11:39 PM | #7 |
Veteran Member
Join Date: Mar 2002
Location: Miles From Nowhere
Posts: 7,420
Likes: 2,587
Liked 4,455 Times in 1,695 Posts
|
Re: Problem cutting a light
Joe, How high can you foot brake it to? I can't imagine a higher starting line RPM not affecting r/t.
Being a Pure Stocker with limited duration, it may indeed go faster leaving at a low RPM. You might end up with an eliminator setting and a different one for qualifying ..Not unheard of.
__________________
We are lucky we don't get as much Government as we pay for..... Will Rogers |
09-22-2014, 12:11 AM | #8 |
Member
Join Date: Feb 2002
Location: Phoenix, AZ
Posts: 163
Likes: 32
Liked 22 Times in 7 Posts
|
Re: Problem cutting a light
The last thing to leave the line is the front wheels...start limiting all the wasted motion that the car goes through........too much front end travel......not enough air in slicks ect....even consider solid body bushings...
|
09-22-2014, 06:20 AM | #9 |
Senior Member
Join Date: Aug 2004
Location: Jacksonville, Florida
Posts: 803
Likes: 6
Liked 20 Times in 12 Posts
|
Re: Problem cutting a light
How much air in the front? With 26" it would take a large change in air pressure to affect rollout. Also, how high can you make the rear tires? Lastly, you sound consistant at the tree. Try (in testing of course), bumping in deeper on the line. Two runs only bumping once, then two runs bumping twice etc. It is worth a shot.
|
09-22-2014, 07:40 AM | #10 |
VIP Member
Join Date: May 2002
Location: Shelby, NC
Posts: 1,667
Likes: 1,717
Liked 1,741 Times in 422 Posts
|
Re: Problem cutting a light
You might want to try a taller rear tire. I believe the class allows a 29.5" x 9".
|
|
|