Opinions or experience with ISKY E-Z roll lifters

Randall Klein · 11-26-2015, 03:20 PM

Anybody using the Isky E-Z roll lifters? I see Bullet advertising same idea

Mark Markow · 11-26-2015, 07:18 PM

I use the crower bushed lifters .best thing I ever did. This is in a 10 k rpm eng. No power loss. Went 3 seasons on the lifters. And I am just going to replace them out of guilt. No more fear of broken needles wrecking everything.

SSGT Mustang · 11-26-2015, 07:51 PM

Mark,

What kind of spring pressure are you running? Also, any brass in the filter from the lifter bushings?

Thanks,

Steve

Mark Markow · 11-26-2015, 08:29 PM

Quote:

Originally Posted by SSGT Mustang

Mark,

What kind of spring pressure are you running? Also, any brass in the filter from the lifter bushings?

Thanks,

Steve

345lbs. on the seat new . and change them if they get down to 320 ish. #1356pac. nothing in the filter, and never see any change in the lash either. also running copper inserts in the pushrod cups. they are a radius cup pushrod and ball adjuster

SSGT Mustang · 11-26-2015, 09:12 PM

Thanks, Mark.

carl hinkson · 11-27-2015, 10:59 AM

I have seen alot of sizing issues with those lifters I have had to buy 2 if not 3 sets to make up one set because of sizing issues.

So make sure you measure every lifter.

http://www.yellowbullet.com/forum/sh...t=lifter+bores

Mark Markow · 11-27-2015, 02:44 PM

Quote:

Originally Posted by carl hinkson

I have seen alot of sizing issues with those lifters I have had to buy 2 if not 3 sets to make up one set because of sizing issues.

So make sure you measure every lifter.

http://www.yellowbullet.com/forum/sh...t=lifter+bores

you mean the isky's? I haven't had any issues with the crower.

pmrphil · 11-27-2015, 06:04 PM

I also have been using the Crower bushed lifters - can't squawk about them at all, but I only rev it to 8,000

carl hinkson · 11-27-2015, 06:50 PM

Quote:

Originally Posted by Mark Markow

you mean the isky's? I haven't had any issues with the crower.

This thread I started was about Crower .903 lifters 3 sets that could not be used.

Crower 842. lifters run right at .841 to small for any GM lifter bore that is .844 which gives you .003 clearance which is to much.

Here it a good video to look over.

I deal with a lot of blocks and check and machine alot of lifters and lifters bores when I machine blocks and have seen about every lifter out there.

Dyno · 11-28-2015, 02:14 PM

thanks Carl.

11-26-2015, 07:18 PM	#2
Mark Markow Senior Member Join Date: Apr 2008 Location: east hartford ct. Posts: 539 Likes: 1 Liked 9 Times in 3 Posts	Re: Opinions or experience with ISKY E-Z roll lifters I use the crower bushed lifters .best thing I ever did. This is in a 10 k rpm eng. No power loss. Went 3 seasons on the lifters. And I am just going to replace them out of guilt. No more fear of broken needles wrecking everything. __________________ Mark Markow 171 ss/tb

11-26-2015, 07:51 PM	#3
SSGT Mustang Member Join Date: Mar 2005 Location: Jersey Posts: 359 Likes: 35 Liked 203 Times in 53 Posts	Re: Opinions or experience with ISKY E-Z roll lifters Mark, What kind of spring pressure are you running? Also, any brass in the filter from the lifter bushings? Thanks, Steve

11-26-2015, 09:12 PM	#5
SSGT Mustang Member Join Date: Mar 2005 Location: Jersey Posts: 359 Likes: 35 Liked 203 Times in 53 Posts	Re: Opinions or experience with ISKY E-Z roll lifters Thanks, Mark.

11-27-2015, 10:59 AM	#6
carl hinkson Member Join Date: Feb 2007 Location: NORTHEAST Posts: 287 Likes: 1 Liked 18 Times in 10 Posts	Re: Opinions or experience with ISKY E-Z roll lifters I have seen alot of sizing issues with those lifters I have had to buy 2 if not 3 sets to make up one set because of sizing issues. So make sure you measure every lifter. http://www.yellowbullet.com/forum/sh...t=lifter+bores

11-27-2015, 06:04 PM	#8
pmrphil Member Join Date: Aug 2010 Location: CT Posts: 384 Likes: 1,254 Liked 247 Times in 106 Posts	Re: Opinions or experience with ISKY E-Z roll lifters I also have been using the Crower bushed lifters - can't squawk about them at all, but I only rev it to 8,000 __________________ Phil Molski S/C 1623

11-26-2015, 03:20 PM	#1
Randall Klein Senior Member Join Date: Dec 2002 Location: Lincoln, Nebraska Posts: 784 Likes: 45 Liked 317 Times in 66 Posts	Opinions or experience with ISKY E-Z roll lifters Anybody using the Isky E-Z roll lifters? I see Bullet advertising same idea

11-28-2015, 02:14 PM	#10
Dyno Senior Member Join Date: Dec 2002 Posts: 870 Likes: 918 Liked 605 Times in 177 Posts	Re: Opinions or experience with ISKY E-Z roll lifters thanks Carl.