|
12-19-2014, 12:35 AM | #1 |
Member
Join Date: Feb 2006
Location: sooner state
Posts: 103
Likes: 2
Liked 51 Times in 21 Posts
|
Edelbrock head accepted for Sbc in S/S ?
Was looking to see if any changes on my combo and seen where there are 3 or 4 edelbrock heads listed as replacements for sbc s/s.When did this happen ? .......Victor
|
12-19-2014, 02:19 AM | #2 |
VIP Member
Join Date: Feb 2014
Location: Lakewood Washington
Posts: 1,407
Likes: 29
Liked 236 Times in 127 Posts
|
Re: Edelbrock head accepted for Sbc in S/S ?
What year and engine? On my page for the 68 Ford, the accepted Canfield and AFR heads are listed by number at the bottom and Edelbrock by name only. Across the top the Edelbrock head numbers are entered in small type like they were an afterthought or correction.
Are they highlighted in yellow? They do that with changes. Dale |
12-19-2014, 04:09 AM | #3 |
Senior Member
Join Date: Jun 2012
Posts: 627
Likes: 517
Liked 881 Times in 198 Posts
|
Re: Edelbrock head accepted for Sbc in S/S ?
Victor, it happened yesterday. J.R.
|
12-19-2014, 10:30 AM | #4 |
VIP Member
Join Date: Oct 2002
Location: Richmond Indiana
Posts: 1,197
Likes: 5
Liked 32 Times in 19 Posts
|
Re: Edelbrock head accepted for Sbc in S/S ?
Good for everyone. Sponsors can get involved. Racers can get new easier to find parts. Only problem is an image thing for the "way it was" starting with all original parts. Spectators can identify the brands and support the makers of the parts..
|
12-19-2014, 12:04 PM | #5 |
Member
Join Date: Feb 2006
Location: sooner state
Posts: 103
Likes: 2
Liked 51 Times in 21 Posts
|
Re: Edelbrock head accepted for Sbc in S/S ?
All i had heard about was the Dart Iron Eagle head being approved,but I'm usually the last to know anyhow......thanks Victor
|
12-19-2014, 01:51 PM | #6 |
VIP Member
Join Date: Feb 2014
Location: Lakewood Washington
Posts: 1,407
Likes: 29
Liked 236 Times in 127 Posts
|
Re: Edelbrock head accepted for Sbc in S/S ?
I see that listing now. Lots of good stuff to stick on a SBC.
Dale |
12-19-2014, 03:12 PM | #7 |
Senior Member
Join Date: Feb 2009
Location: Columbus, Indiana
Posts: 517
Likes: 139
Liked 301 Times in 73 Posts
|
Re: Edelbrock head accepted for Sbc in S/S ?
I did a search on all these numbers and found nothing other than 608879 part number. But that number isn't listed with the last digit of 9. When are they (Edelbrock) going to make them?
Ernie Neal SS 354 |
12-19-2014, 04:47 PM | #8 |
Live Reporter
Join Date: May 2006
Location: Dripping Springs, Tx
Posts: 2,698
Likes: 185
Liked 503 Times in 126 Posts
|
Re: Edelbrock head accepted for Sbc in S/S ?
Called and found out 283 not approved to use aftermarket heads. The only head I could find(like Ernie stated) is a 1.94 valve 185cc head. That wont work anyway for a 283 without a ton of work. I was told the other 3 not available yet.
__________________
Ed Carpenter 2005 Chevy Cobalt A/SM Race Engine Development |
12-20-2014, 01:01 AM | #9 |
VIP Member
Join Date: Feb 2014
Location: Lakewood Washington
Posts: 1,407
Likes: 29
Liked 236 Times in 127 Posts
|
Re: Edelbrock head accepted for Sbc in S/S ?
Based on the code used on the stock car classification guide, only engines with "$" (might be a sub section symbol) under the CID can run the newly listed heads. Seems to start with 327s.
Dale |
|
|