|
11-26-2015, 03:20 PM | #1 |
Senior Member
Join Date: Dec 2002
Location: Lincoln, Nebraska
Posts: 784
Likes: 45
Liked 317 Times in 66 Posts
|
Opinions or experience with ISKY E-Z roll lifters
Anybody using the Isky E-Z roll lifters? I see Bullet advertising same idea
|
11-26-2015, 07:18 PM | #2 |
Senior Member
Join Date: Apr 2008
Location: east hartford ct.
Posts: 539
Likes: 1
Liked 9 Times in 3 Posts
|
Re: Opinions or experience with ISKY E-Z roll lifters
I use the crower bushed lifters .best thing I ever did. This is in a 10 k rpm eng. No power loss. Went 3 seasons on the lifters. And I am just going to replace them out of guilt. No more fear of broken needles wrecking everything.
__________________
Mark Markow 171 ss/tb |
11-26-2015, 07:51 PM | #3 |
Member
Join Date: Mar 2005
Location: Jersey
Posts: 359
Likes: 35
Liked 203 Times in 53 Posts
|
Re: Opinions or experience with ISKY E-Z roll lifters
Mark,
What kind of spring pressure are you running? Also, any brass in the filter from the lifter bushings? Thanks, Steve |
11-26-2015, 08:29 PM | #4 |
Senior Member
Join Date: Apr 2008
Location: east hartford ct.
Posts: 539
Likes: 1
Liked 9 Times in 3 Posts
|
Re: Opinions or experience with ISKY E-Z roll lifters
345lbs. on the seat new . and change them if they get down to 320 ish. #1356pac. nothing in the filter, and never see any change in the lash either. also running copper inserts in the pushrod cups. they are a radius cup pushrod and ball adjuster
__________________
Mark Markow 171 ss/tb |
11-26-2015, 09:12 PM | #5 |
Member
Join Date: Mar 2005
Location: Jersey
Posts: 359
Likes: 35
Liked 203 Times in 53 Posts
|
Re: Opinions or experience with ISKY E-Z roll lifters
Thanks, Mark.
|
11-27-2015, 10:59 AM | #6 |
Member
Join Date: Feb 2007
Location: NORTHEAST
Posts: 287
Likes: 1
Liked 18 Times in 10 Posts
|
Re: Opinions or experience with ISKY E-Z roll lifters
I have seen alot of sizing issues with those lifters I have had to buy 2 if not 3 sets to make up one set because of sizing issues.
So make sure you measure every lifter. http://www.yellowbullet.com/forum/sh...t=lifter+bores |
11-27-2015, 02:44 PM | #7 | |
Senior Member
Join Date: Apr 2008
Location: east hartford ct.
Posts: 539
Likes: 1
Liked 9 Times in 3 Posts
|
Re: Opinions or experience with ISKY E-Z roll lifters
Quote:
__________________
Mark Markow 171 ss/tb |
|
11-27-2015, 06:04 PM | #8 |
Member
Join Date: Aug 2010
Location: CT
Posts: 387
Likes: 1,259
Liked 250 Times in 107 Posts
|
Re: Opinions or experience with ISKY E-Z roll lifters
I also have been using the Crower bushed lifters - can't squawk about them at all, but I only rev it to 8,000
__________________
Phil Molski S/C 1623 |
11-27-2015, 06:50 PM | #9 | |
Member
Join Date: Feb 2007
Location: NORTHEAST
Posts: 287
Likes: 1
Liked 18 Times in 10 Posts
|
Re: Opinions or experience with ISKY E-Z roll lifters
Quote:
Crower 842. lifters run right at .841 to small for any GM lifter bore that is .844 which gives you .003 clearance which is to much. Here it a good video to look over. I deal with a lot of blocks and check and machine alot of lifters and lifters bores when I machine blocks and have seen about every lifter out there. |
|
11-28-2015, 02:14 PM | #10 |
Senior Member
Join Date: Dec 2002
Posts: 870
Likes: 920
Liked 605 Times in 177 Posts
|
Re: Opinions or experience with ISKY E-Z roll lifters
thanks Carl.
|
|
|