|
|
03-25-2017, 09:12 AM | #1 |
Junior Member
Join Date: Aug 2010
Posts: 53
Likes: 0
Liked 2 Times in 2 Posts
|
Small block ford crank scraper
Looking for information on Pros or cons for running a crank scraper in a small block Ford and also which would be the best one to run
|
03-25-2017, 09:27 AM | #2 |
VIP Member
Join Date: Jan 2003
Location: Allentown,PA
Posts: 2,436
Likes: 776
Liked 700 Times in 204 Posts
|
Re: Small block ford crank scraper
I've had improvements in oil control and some modest power increases on the stock pan AMC's I build using scrapers.
These guys offer a scraper for almost any engine and the rough fit is very close. only minor trimming is needed.http://www.crank-scrapers.com/index.html
__________________
Tom Goldman 1500 SG , 1506 STK |
03-25-2017, 02:24 PM | #3 | |
VIP Member
Join Date: Feb 2003
Location: Glendale, Arizona
Posts: 2,991
Likes: 693
Liked 1,457 Times in 543 Posts
|
Re: Small block ford crank scraper
Quote:
|
|
03-26-2017, 11:10 AM | #4 |
Member
Join Date: Jul 2007
Location: Pottstown,Pa.
Posts: 121
Likes: 24
Liked 11 Times in 8 Posts
|
Re: Small block ford crank scraper
My experience with crankscrapers.com is don't waste your time. Ordered one, was told it was special order. Had to pay up front for it. Understand that, but got a lot of promises, completion dates, tracking numbers and after a year got a refund.
|
03-26-2017, 11:43 AM | #5 | |
Member
Join Date: Jun 2007
Location: Federal Way, WA
Posts: 233
Likes: 24
Liked 147 Times in 47 Posts
|
Re: Small block ford crank scraper
Quote:
https://www.summitracing.com/parts/ctr-20-830
__________________
Brian Thompson NHRA Stock / Super Stock Class P/SA 6665 SS/MA 6665 Last edited by fordteacherguy; 03-26-2017 at 06:24 PM. |
|
03-26-2017, 01:22 PM | #6 |
Senior Member
Join Date: Nov 2007
Location: Div. 6, Eastern, WA
Posts: 694
Likes: 2,260
Liked 219 Times in 105 Posts
|
Re: Small block ford crank scraper
Who makes one for a 351C ?
__________________
Dave Noll, E/FS ,L/SA 6526 |
03-26-2017, 07:31 PM | #7 |
Member
Join Date: Jun 2007
Location: Federal Way, WA
Posts: 233
Likes: 24
Liked 147 Times in 47 Posts
|
Re: Small block ford crank scraper
__________________
Brian Thompson NHRA Stock / Super Stock Class P/SA 6665 SS/MA 6665 |
03-27-2017, 08:01 AM | #8 |
Member
Join Date: Dec 2013
Posts: 311
Likes: 2
Liked 9 Times in 8 Posts
|
Re: Small block ford crank scraper
Moroso 22939
Milodon 32222 both are nice windage trays but you need to make your own scraper its not hard get some cardboard and make a template and get after it. The oiling system of a Ford Cleveland needs major work, up above is just a start, and I know guys will say they did this and they did that but the fact is... to make any kind of power and make it last while restricted to a stock pan takes work
__________________
__________________ Bill Diehl B200 C/D STK |
03-27-2017, 09:32 AM | #9 |
VIP Member
Join Date: Feb 2014
Location: Lakewood Washington
Posts: 1,407
Likes: 29
Liked 236 Times in 127 Posts
|
Re: Small block ford crank scraper
I have the following windage tray on my BOSS block 302:
https://www.summitracing.com/parts/c...view/make/ford It required a bolt kit for a 351 due to the 1/2 in main caps and a little hammer time to fit just right. The motor has been fired and hasn't spit anything out.
__________________
Dale Shearon 68 Mustang 6394 Last edited by FireSale; 03-27-2017 at 09:40 AM. |
03-26-2017, 01:54 PM | #10 | |
Junior Member
Join Date: Aug 2010
Posts: 53
Likes: 0
Liked 2 Times in 2 Posts
|
Re: Small block ford crank scraper
Quote:
|
|
|
|