CLASS RACER FORUM
Page 3 of 3 12 3
Show 40 post(s) from this thread on one page

CLASS RACER FORUM (https://classracer.com/classforum/index.php)
-   Stock and Super Stock Tech (https://classracer.com/classforum/forumdisplay.php?f=4)
-   -   SBC Pink Rods (https://classracer.com/classforum/showthread.php?t=74685)

1347 11-11-2019 10:18 AM
Re: SBC Pink Rods
 
Quote:
Originally Posted by Dan Fahey (Post 601455)
They are already in the engine.
Budd Rowe fitted the Pink Rods with Forged pistons, about 8 years ago.
Engine has been in storage and Rockville Ring and Bearing just went through the block with fresh bearings.

If i kept them what RPM range would be safe?
One racer posted he used them in a SS engine at much higher rpm than 7000 rpm.

Only have so much tine and money..

D
What rpm will your combo see? Some combos will never see 7000 rpm, some will go over 8000 as you noted.

If you are second guessing yourself and want to upgrade, get the Eagles. I run them in my Boss 302, making 540hp shifting at 8700 and going thru at 8900 in good air with no problems. Just make sure you get them with the arp2000 bolts, and check the big ends and small ends.
For 500.00 you can't go wrong.

Eman 11-11-2019 05:54 PM
Re: SBC Pink Rods
 
Have they been bushed for floating pins or are they still press fit which is what they were new.

Makinchips 11-12-2019 12:41 PM
Re: SBC Pink Rods
 
Are these Hbeam rods or I beams that are turned 8000?

Ed Wright 11-12-2019 08:56 PM
Re: SBC Pink Rods
 
Quote:
Originally Posted by 1347 (Post 601491)
What rpm will your combo see? Some combos will never see 7000 rpm, some will go over 8000 as you noted.

If you are second guessing yourself and want to upgrade, get the Eagles. I run them in my Boss 302, making 540hp shifting at 8700 and going thru at 8900 in good air with no problems. Just make sure you get them with the arp2000 bolts, and check the big ends and small ends.
For 500.00 you can't go wrong.
I tried a set of those, cheap and a set on the shelf here in town. I may be too anal, but the big ends were all over the place. Had to re-size them, and length varied. Had to sand some piston tops to set the deck. (No mill)
Mine only goes ~8400 in the lights. Best I have found are Manley. Light, and all sizes dead nuts. This was three years ago. Eagle may be better now.

Dan Fahey 11-12-2019 11:24 PM
Re: SBC Pink Rods
 
Sucks moving from Pure Stock to Stock..
Both engines SBC and LT1 were originally designed for under 7000 rpm.
With stock stuff...

Prepped Pinks and LT1 rods seem to be ok to 7200 rpm.
Stockers are mini SuperStock Engines hitting ridiculous RPM.
Above that a lot more costs and still questionable reliability.
Then adding roll bars, reinforced rear ends, replacing harnesses every two years, European priced fuel for racing.

Where is the fun?


All times are GMT -4. The time now is 12:57 PM.
Page 3 of 3 12 3
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright Class Racer.com. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.