Mopar A Body/B-RB Engine racers ???
 

Anyone have recent experience using a commercially available header on a B/RB engine in Stock Eliminator? Trying to avoid having headers made on the car, looking for something that will bolt on.



Thanks

Re: Mopar A Body/B-RB Engine racers ???
 

dart or cuda? the only ones i know about are fenderwell headers

Re: Mopar A Body/B-RB Engine racers ???
 

TTI or ARH? I know TTI sells them

Re: Mopar A Body/B-RB Engine racers ???
 

1967-1976 A Body - both Dodge and Plymouth, have the same engine compartment layout. Don't want fenderwell headers.


Thanks.

Re: Mopar A Body/B-RB Engine racers ???
 

I run 2 Inch under chassis headers by TTI on my
10 Second 1969 A Body Valiant.

I can check the number on them when I get back from Division 7
races next week.

There are several Fender well Headers for that combo but they are
all a pain for tire clearance!

They are expensive!

Re: Mopar A Body/B-RB Engine racers ???
 

For the life of me I can’t remember the name but there were sets made where 3 tubes where inside the frame and one went out the front end alignment hole back under the car, they fit well with no cutting. Maybe someone else can remember

Re: Mopar A Body/B-RB Engine racers ???
 

McCandless?

Re: Mopar A Body/B-RB Engine racers ???
 

Pro Parts used to make some nice RB headers for an A-body.

Jeff Ross had some nice headers for sale on Face Booger.

Re: Mopar A Body/B-RB Engine racers ???
 

I had a set of Jardines like that. In the previous century lol

Re: Mopar A Body/B-RB Engine racers ???
 

‘Pro Parts’ sounds right. It WAS last century lol, a friend put them on his 71 dart, 440 engine around 1990 or so fit much better than the fender wells.

Re: Mopar A Body/B-RB Engine racers ???
 

I have a set of parts pro headers on a 75 duster 383. Two tubes go through the fender well on the driver side one on the passenger side. Fit well and will work with power steering. May be big for a stocker, 2”-21/8” with 3.5” collector. Bob Mazzolini used to sell them.

Re: Mopar A Body/B-RB Engine racers ???
 

Was that "Jardine" headers??
Could it have been "Stahl"

Re: Mopar A Body/B-RB Engine racers ???
 

It is my understanding that the old Bill Bagshaw "Pro Parts" headers are the same headers currently sold by TTI. Years ago, a buddy had a set of the Pro Parts headers on his 70 Duster with a 440, and they fit great.

Re: Mopar A Body/B-RB Engine racers ???
 

TTI makes the headers for Mazzolini. TTI offers its own small tube chassis header.

Re: Mopar A Body/B-RB Engine racers ???
 

My TTIs under chassis headers are 2 inch tubes.
A couple of the plugs are a bit of a pain!

Re: Mopar A Body/B-RB Engine racers ???
 

I am not a Mopar expert in the least. But just ended up with a set of Big block Mopar headers. As close as we can tell from researching. they should fit 67-74 b-body and e body, 70-74 Barracuda and 75-74 fury, I can get some pictures posted later today if you would like a look.

Re: Mopar A Body/B-RB Engine racers ???
 

Finally talked to him today, he bought them from M Candless, said they were their headers

Re: Mopar A Body/B-RB Engine racers ???
 

TTI makes the ProParts headers exclusively for us at Bob Mazzolini Racing. We are currently having a run of 25 sets being made now. 2" to 2 1/8" step. We are taking preorders and should start shipping in the next few weeks. Give a call if interested. 951-787-8783

Re: Mopar A Body/B-RB Engine racers ???
 

Those are Fenderwell Exit?

Re: Mopar A Body/B-RB Engine racers ???
 

Semi fenderwell. Two tubes driver side, one tube passenger side.


https://bobmazzoliniracing.com/store...ERS/p/48439871

Re: Mopar A Body/B-RB Engine racers ???
 

Pro Parts headers from Bob are good pieces for sure.

Re: Mopar A Body/B-RB Engine racers ???
 

Thanks, all good info.