CLASS RACER FORUM - View Single Post - Strange front hubs & Moser axles both w/ceramic bearings

RUQWIKR · 05-03-2018, 08:59 PM

LOWERED PRICES: SOLD ALL BUT HUBS W/O THE CERAMIC BEARINGS

SUMMARY OF PARTS:
- Pair of Strange B1324a brake hubs with billet caps, ceramic bearings, Ti studs - SOLD (DAVE M. in Texas)
- Pair of Strange B1324a brake hubs with Ti studs
- Pair of Moser gun-drilled 33-spline lightened axles with Ti studs & ceramic bearings - SOLD (DAVE M. in Texas)
- Set of Strange 2-piece aluminum hat lightweight rotors (front & rear) - SOLD (DAVE M. in Texas)

Been a long time follower on Class Racer. Sold my 01 Firebird drag car recently and have some leftover parts. Did most of these upgrades late in 2014. Never got the car out for the rest 2014, none in 2015, three runs in February 2016, none since.

I have a pair of Strange front brake hubs (B1324a PN) with custom titanium studs (Tapered Socket Cap Head Screws) and ceramic bearings. The billet Strange hubs and caps were bought new from Strange and sent off to Performance Bearings for machining and bearing install. The hubs have custom machined Titanium studs (1/2"-20). Bearing ID is ~1.25".

The assemblies have only three runs on them in February 2016. I have $1500 in them. Will take $745 shipped in lower 48 states (residential or business, no P.O. boxes). If you do PayPal, I won't tack on any fees, but, the shipping address needs to be your PayPal address. I'm in the Dallas, Texas area if local / somewhat local, we can meet up.

http://www.performancebearing.com/dragracing.html

Talked with Strange today. They said B1324a hubs and bearing size should fit their race kits on 1st, 2nd, 3rd, and 4th Gen Camaro / Firebirds, the 79-87 G-bodies, and other kits.

I also have a new set of the Strange billet B1324a hubs with Timken races installed by Strange. They also have Titanium 1/2"-20 custom studs in them. I'll take $295 shipped for those. Same payment / shipping conditions as above.

Also selling a pair of custom Moser axles from my 01 Firebird. They have 12 runs on the axles but only 3 runs on the ceramic bearings from Performance Bearings. They are 33-spline, gun drilled, star flanged for lightening, and have Mark Williams Titanium drive studs installed. Studs are ~2.93" long in total, ~2.074" from front axle flange face with ~1.16" thread length of 5/8"-18. No twist on the splines noticed.

I have tried to take some measurements using the .pdf as a guide:

A: ~3.05", B: ~1.30" and 2.62" to bearing outside face (ceramic bearing with o-ring ~3.15" OD & 0.83" wide)
C: ~31.50" (~3.17" spline length)
H: ~1.90"
K: ~5.64"

Axle shaft diameter at splines ~1.41"

https://summitracing.custhelp.com/ci...order+form.pdf

I'll take $399 shipped with same payment / shipping conditions as above for the axles.

Finally, for now, I have a set of front and rear Strange 2-piece aluminum hat rotors. All four have three runs on them. For specs, see the link. Not sure what all they fit besides F-cars like mine. Saves rotating weight over their regular brake rotors. I'll take $299 shipped with same payment / shipping conditions as above for the rotors.

https://www.strangeengineering.net/p...ly-rh-ea.html/

My boys are adults now and never got the drag racing bug.

Still will be a rabid drag racing fan and supporter.

Email is ruqwikr@yahoo.com. Have plenty of pics available. Serious middle age seller that won't waste your time, and let's keep it that way vice versa, too.

Take care. Dave

(HOPEFULLY THESE LINKS WORK TO PICS)
https://drive.google.com/open?id=1qs...5qChoW3y0lNXT1

https://drive.google.com/open?id=10G...CWCAQP-IxlKKwN

https://drive.google.com/open?id=1yv...fY1Y1SRVQwFIqI

https://drive.google.com/open?id=1NO...aH0Q_rbpKYTmKv

https://drive.google.com/open?id=1mg...F3lHR0rkGhTUul

https://drive.google.com/open?id=16G...56ir746Wrssrko

https://drive.google.com/open?id=1jI...7AaNvetgTBTDw6

https://drive.google.com/open?id=1DF...AisEMF15Eooev_

https://drive.google.com/open?id=1xb...73mnuIV_fy71zG

05-03-2018, 08:59 PM	#1
RUQWIKR Junior Member Join Date: Dec 2007 Posts: 4 Likes: 0 Liked 0 Times in 0 Posts	Strange front hubs & Moser axles both w/ceramic bearings LOWERED PRICES: SOLD ALL BUT HUBS W/O THE CERAMIC BEARINGS SUMMARY OF PARTS: - Pair of Strange B1324a brake hubs with billet caps, ceramic bearings, Ti studs - SOLD (DAVE M. in Texas) - Pair of Strange B1324a brake hubs with Ti studs - Pair of Moser gun-drilled 33-spline lightened axles with Ti studs & ceramic bearings - SOLD (DAVE M. in Texas) - Set of Strange 2-piece aluminum hat lightweight rotors (front & rear) - SOLD (DAVE M. in Texas) Been a long time follower on Class Racer. Sold my 01 Firebird drag car recently and have some leftover parts. Did most of these upgrades late in 2014. Never got the car out for the rest 2014, none in 2015, three runs in February 2016, none since. I have a pair of Strange front brake hubs (B1324a PN) with custom titanium studs (Tapered Socket Cap Head Screws) and ceramic bearings. The billet Strange hubs and caps were bought new from Strange and sent off to Performance Bearings for machining and bearing install. The hubs have custom machined Titanium studs (1/2"-20). Bearing ID is ~1.25". The assemblies have only three runs on them in February 2016. I have $1500 in them. Will take $745 shipped in lower 48 states (residential or business, no P.O. boxes). If you do PayPal, I won't tack on any fees, but, the shipping address needs to be your PayPal address. I'm in the Dallas, Texas area if local / somewhat local, we can meet up. http://www.performancebearing.com/dragracing.html Talked with Strange today. They said B1324a hubs and bearing size should fit their race kits on 1st, 2nd, 3rd, and 4th Gen Camaro / Firebirds, the 79-87 G-bodies, and other kits. I also have a new set of the Strange billet B1324a hubs with Timken races installed by Strange. They also have Titanium 1/2"-20 custom studs in them. I'll take $295 shipped for those. Same payment / shipping conditions as above. Also selling a pair of custom Moser axles from my 01 Firebird. They have 12 runs on the axles but only 3 runs on the ceramic bearings from Performance Bearings. They are 33-spline, gun drilled, star flanged for lightening, and have Mark Williams Titanium drive studs installed. Studs are ~2.93" long in total, ~2.074" from front axle flange face with ~1.16" thread length of 5/8"-18. No twist on the splines noticed. I have tried to take some measurements using the .pdf as a guide: A: ~3.05", B: ~1.30" and 2.62" to bearing outside face (ceramic bearing with o-ring ~3.15" OD & 0.83" wide) C: ~31.50" (~3.17" spline length) H: ~1.90" K: ~5.64" Axle shaft diameter at splines ~1.41" https://summitracing.custhelp.com/ci...order+form.pdf I'll take $399 shipped with same payment / shipping conditions as above for the axles. Finally, for now, I have a set of front and rear Strange 2-piece aluminum hat rotors. All four have three runs on them. For specs, see the link. Not sure what all they fit besides F-cars like mine. Saves rotating weight over their regular brake rotors. I'll take $299 shipped with same payment / shipping conditions as above for the rotors. https://www.strangeengineering.net/p...ly-rh-ea.html/ My boys are adults now and never got the drag racing bug. Still will be a rabid drag racing fan and supporter. Email is ruqwikr@yahoo.com. Have plenty of pics available. Serious middle age seller that won't waste your time, and let's keep it that way vice versa, too. Take care. Dave (HOPEFULLY THESE LINKS WORK TO PICS) https://drive.google.com/open?id=1qs...5qChoW3y0lNXT1 https://drive.google.com/open?id=10G...CWCAQP-IxlKKwN https://drive.google.com/open?id=1yv...fY1Y1SRVQwFIqI https://drive.google.com/open?id=1NO...aH0Q_rbpKYTmKv https://drive.google.com/open?id=1mg...F3lHR0rkGhTUul https://drive.google.com/open?id=16G...56ir746Wrssrko https://drive.google.com/open?id=1jI...7AaNvetgTBTDw6 https://drive.google.com/open?id=1DF...AisEMF15Eooev_ https://drive.google.com/open?id=1xb...73mnuIV_fy71zG Last edited by RUQWIKR; 06-24-2018 at 07:20 PM.