|
![]() |
#1 |
Junior Member
Join Date: Apr 2013
Posts: 43
Likes: 73
Liked 1 Time in 1 Post
|
![]()
I need to have a new set of step headers built for a SBC (327 & 350 combinations) for a 1992 Super Stock GT/GA Camaro.
Any recommendations would be very much appreciated. Located in Langhorne, PA area. Thank you! Kev Last edited by Kevin J. McHugh; 08-29-2013 at 02:59 PM. |
![]() |
![]() |
![]() |
#2 |
Junior Member
Join Date: Mar 2003
Location: Detroit,MI
Posts: 81
Likes: 28
Liked 29 Times in 14 Posts
|
![]()
Hi Kevin,
I;m not sure where you are located, but if your in the OHIO area, I would recommend KromerKraft. You did not mention the make of the vehicle. RonP |
![]() |
![]() |
![]() |
#3 |
Junior Member
Join Date: Oct 2009
Posts: 35
Likes: 0
Liked 0 Times in 0 Posts
|
![]()
post looks like 1992 Camaro SS to me
|
![]() |
![]() |
![]() |
#4 |
Member
Join Date: Dec 2003
Location: Neosho, MO
Posts: 215
Likes: 0
Liked 59 Times in 13 Posts
|
![]()
I bought my header material and collectors from Mark @ Performance Welding. I then had Larry Larson in KC, MO build my headers to the specs supplied by Mark. Obviously, KC is too far but having Mark help someone local build them to his specs would be a wise investment.
|
![]() |
![]() |
![]() |
#5 |
Veteran Member
Join Date: Mar 2005
Location: Sand Springs, OK
Posts: 8,132
Likes: 896
Liked 390 Times in 170 Posts
|
![]()
Might think about Jere Stahl. He just picked my car up a little.
__________________
Ed Wright 4156 SS/JA |
![]() |
![]() |
![]() |
#6 |
VIP Member
Join Date: Jan 2009
Location: Maryland
Posts: 1,733
Likes: 1,599
Liked 459 Times in 90 Posts
|
![]()
Kevin is Beco still around your area? He made great headers in the day.
__________________
Bob Bender 144 O/SA 2010-2012 National Record Holder |
![]() |
![]() |
![]() |
#7 |
VIP Member
Join Date: Mar 2010
Location: Newport News, VA
Posts: 1,435
Likes: 371
Liked 129 Times in 59 Posts
|
![]()
I'd have to agree with Ed, Stahl would be a good choice in a custom-made racing header.
http://stahlheaders.com/Frame%20New%20Drag.htm
__________________
Lew Silverman #2070 "The Wagon Master" N/SA |
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: Oct 2002
Location: Pittsburgh
Posts: 575
Likes: 298
Liked 747 Times in 136 Posts
|
![]()
Hate to be the cheap sob here, but Hooker makes a header for that application. Its what I have on my car (1992 Camaro 350/255/294). Granted Im not real fast, but thats not because of the headers.... They are 1 3/4" to 1 7/8" to 2" step headers. There is a badge on them "Hooker SuperCompetition Headers" don't think there is a part number, but I'll go look in a bit...
Kevin |
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: Jan 2007
Location: N/A
Posts: 882
Likes: 0
Liked 22 Times in 22 Posts
|
![]()
If it's allowed in super stock, use the half inch header plates, matched perfectly to your exhaust ports, and the exhaust will pick up 10, to 20 cfm. Then use 1 and 7\8" to 2." Just my opinion.
__________________
don,t have one |
![]() |
![]() |
![]() |
|
|