Moroso front springs

J.R. Haddad · 07-31-2014, 11:02 PM

Anybody who has put Moroso Springs in a 1982-1992 Camaro SBC Stocker, how much did you have to cut if any ? I.E. 1/2 coil, 3/4, full
coil, etc. to get the ride height you wanted. Thanks, J.R.

Mike Taylor 3601 · 08-01-2014, 09:24 AM

Best to install them move car around,and see how ride height is before doing anything
Mike Taylor 3601

Eman · 08-01-2014, 09:43 AM

I bought a used set, previous owner said he cut 1/2 coil off. I installed them like that and the car sat a little high. I ran it like that and felt no difference from the 6 cyl springs. I took it apart and cut another 1/2 coil. I honestly can't remember if that was right or if I did it again, but when the car sat right there was a world of difference in how the car worked. It stopped just popping up and dropping back down on launch. It started lifting and staying up.
One thing for sure is use a Snapon,Branick spring compressor. break the A arm at the ball joint and use the spring compressor to collapse the spring as much as possible. I have to use a short piece of pipe on the center screw to keep it from hitting the frame at the top when installing the spring. I pull it down tight with an impact gun. It's not for the faint of heart. You can remove the compressor once the ball joint is attached and drop it out the bottom of the control arm
http://www.ebay.com/itm/COIL-SPRING-...item3f3a71b012
This is the style compressor I use with the fork at the bottom. Be sure it's a name brand piece and not some China junk.

gmeyer · 08-01-2014, 03:20 PM

SBC 3rd gen f body 3/4 of a coil works real good and OTC makes the best spring comp. for these cars. The hook still does not work very well
on these cars.

Jeff Niceswanger · 08-01-2014, 04:36 PM

What Greg said, although I cut 1 1/8 to 1/1/4 off and change them every 2 or 3 years...That puller is the berry's. Greg has the part #. He has a heavier 400 Pontiac and I have a small block Chevy......Don't cut anymore than 1 1/4 off or you will be buying another set.......I know

Pistol Pete · 08-01-2014, 05:52 PM

Quote:

Originally Posted by gmeyer

SBC 3rd gen f body 3/4 of a coil works real good and OTC makes the best spring comp. for these cars. The hook still does not work very well
on these cars.

I'm guessing your talking about a Stocker right ??

Tim Lisson · 08-04-2014, 08:58 AM

I cut 1 full coil off mine and it's not enough, I would go with the 1 1/8 that was suggested by Jeff.

Tim

Terry Drinkwater · 08-04-2014, 04:44 PM

We used to heat 'em on the car, alternating sides until the ride height was where we wanted.

TurboBuick6 · 08-06-2014, 10:02 AM

Quote:

Originally Posted by Terry Drinkwater

We used to heat 'em on the car, alternating sides until the ride height was where we wanted.

That is awesome right there. Keep the rate in the spring and just drop the free length.

07-31-2014, 11:02 PM	#1
J.R. Haddad Senior Member Join Date: Jun 2012 Posts: 783 Likes: 928 Liked 1,462 Times in 307 Posts	Moroso front springs Anybody who has put Moroso Springs in a 1982-1992 Camaro SBC Stocker, how much did you have to cut if any ? I.E. 1/2 coil, 3/4, full coil, etc. to get the ride height you wanted. Thanks, J.R.

08-01-2014, 09:24 AM	#2
Mike Taylor 3601 VIP Member Join Date: Oct 2008 Location: Somerset,Ky Posts: 1,364 Likes: 340 Liked 281 Times in 97 Posts	Re: Moroso front springs Best to install them move car around,and see how ride height is before doing anything Mike Taylor 3601

08-01-2014, 09:43 AM	#3
Eman Member Join Date: May 2014 Location: E TN Posts: 469 Likes: 16 Liked 133 Times in 76 Posts	Re: Moroso front springs I bought a used set, previous owner said he cut 1/2 coil off. I installed them like that and the car sat a little high. I ran it like that and felt no difference from the 6 cyl springs. I took it apart and cut another 1/2 coil. I honestly can't remember if that was right or if I did it again, but when the car sat right there was a world of difference in how the car worked. It stopped just popping up and dropping back down on launch. It started lifting and staying up. One thing for sure is use a Snapon,Branick spring compressor. break the A arm at the ball joint and use the spring compressor to collapse the spring as much as possible. I have to use a short piece of pipe on the center screw to keep it from hitting the frame at the top when installing the spring. I pull it down tight with an impact gun. It's not for the faint of heart. You can remove the compressor once the ball joint is attached and drop it out the bottom of the control arm http://www.ebay.com/itm/COIL-SPRING-...item3f3a71b012 This is the style compressor I use with the fork at the bottom. Be sure it's a name brand piece and not some China junk.

08-01-2014, 03:20 PM	#4
gmeyer Member Join Date: Jan 2003 Posts: 183 Likes: 45 Liked 35 Times in 16 Posts	Re: Moroso front springs SBC 3rd gen f body 3/4 of a coil works real good and OTC makes the best spring comp. for these cars. The hook still does not work very well on these cars.

08-01-2014, 04:36 PM	#5
Jeff Niceswanger Senior Member Join Date: Jul 2003 Posts: 870 Likes: 673 Liked 962 Times in 352 Posts	Re: Moroso front springs What Greg said, although I cut 1 1/8 to 1/1/4 off and change them every 2 or 3 years...That puller is the berry's. Greg has the part #. He has a heavier 400 Pontiac and I have a small block Chevy......Don't cut anymore than 1 1/4 off or you will be buying another set.......I know __________________ Jeff Niceswanger 3740 SS

08-04-2014, 08:58 AM	#7
Tim Lisson Member Join Date: Aug 2003 Location: Solon Springs, WI Posts: 166 Likes: 0 Liked 0 Times in 0 Posts	Re: Moroso front springs I cut 1 full coil off mine and it's not enough, I would go with the 1 1/8 that was suggested by Jeff. Tim

08-04-2014, 04:44 PM	#8
Terry Drinkwater Junior Member Join Date: Mar 2014 Location: Alabama Posts: 81 Likes: 1 Liked 22 Times in 9 Posts	Re: Moroso front springs We used to heat 'em on the car, alternating sides until the ride height was where we wanted.