|
![]() |
#1 |
VIP Member
Join Date: Oct 2007
Posts: 1,168
Likes: 487
Liked 346 Times in 126 Posts
|
![]()
I am going to be pulling apart a bracket 340 and I am going to re-use the rod and pistons. And I have been told by very knowledgeable people not to use a numbered punch on the rods since they can induce stress risers. What is the best way to make these so they go back into the correct hole?
|
![]() |
![]() |
![]() |
#2 |
Member
Join Date: Jul 2003
Posts: 235
Likes: 0
Liked 6 Times in 4 Posts
|
![]()
Sounds like a BS story. Most factory rods are stamped with a numbered punch and they hold up just fine.
|
![]() |
![]() |
![]() |
#3 |
VIP Member
Join Date: Mar 2010
Location: Newport News, VA
Posts: 1,435
Likes: 371
Liked 129 Times in 59 Posts
|
![]()
How about one of those electric etching tools you can pick up at Sears or Harbor Freight for less than $20? That would solve the problem of being a little too "heavy-handed" with a punch and ball-peen hammer.
__________________
Lew Silverman #2070 "The Wagon Master" N/SA |
![]() |
![]() |
![]() |
#4 |
VIP Member
Join Date: Oct 2007
Posts: 1,168
Likes: 487
Liked 346 Times in 126 Posts
|
![]()
Jason, i want to return each piston and rod to the hole they came from, and no mopar rods are not numbered to go into a particular cylinder. And thanks Lew, I will look into that. I was also considering the pens that junk yards use to mark parts.
Last edited by David Lee; 06-18-2017 at 10:22 PM. Reason: thanking Lew |
![]() |
![]() |
![]() |
#5 |
VIP Member
Join Date: Jun 2009
Location: Boulder City, Nevada 89005
Posts: 2,731
Likes: 2,795
Liked 2,471 Times in 696 Posts
|
![]()
David: I am surprised....Every 340 production rod I have every seen
is numbered 1 to 8 to Cylinder. Never had a problem stamping including pistons. Excepting Some Chinese aftermarket stuff (Re: 440 Source rods)
__________________
John Irving 741 Stock 741 Super Stock |
![]() |
![]() |
![]() |
#6 |
Member
Join Date: Apr 2005
Posts: 494
Likes: 6
Liked 25 Times in 16 Posts
|
![]()
Almost all or all of the Chrysler V8s I've taken apart had the rods numbered (subject to old geezer memory). The number was maybe .09"-.12" tall as best as I can remember. I have a 340 on the engine stand, so I'll take a look tomorrow once the rain blows through. I probably wouldn't stamp the rods once the big ends were resized and new rod bolts installed. I think the rod bore only has a .0005" total tolerance on the bore size.
__________________
Mopar 2 Ya! |
![]() |
![]() |
![]() |
#7 |
VIP Member
Join Date: Oct 2007
Posts: 1,168
Likes: 487
Liked 346 Times in 126 Posts
|
![]()
guess I should have been a bit more specific. This engine was built by someone unknown and it is not my engine. It appears to have scat rods and kb pistons. I went down to an auto parts store and bought the pens and was able to mark the piston tops.
|
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: Nov 2005
Location: Pinckney, Michigan
Posts: 507
Likes: 399
Liked 263 Times in 68 Posts
|
![]()
Magic marker.
__________________
John Dinkel 3295 STK |
![]() |
![]() |
![]() |
#9 |
Junior Member
Join Date: Dec 2008
Posts: 76
Likes: 0
Liked 1 Time in 1 Post
|
![]()
Dave,
Clean the area with lacquer thinner. Put dab of dykem on them, use a scribe to make the #. Been doing it for years stays on a long time. |
![]() |
![]() |
![]() |
#10 |
VIP Member
Join Date: Oct 2007
Posts: 1,168
Likes: 487
Liked 346 Times in 126 Posts
|
![]()
thanks for the idea
|
![]() |
![]() |
![]() |
|
|