|
|
12-15-2014, 06:38 PM
|
#1 |
|
Senior Member
Join Date: Jun 2012
Posts: 788
Likes: 947
Liked 1,471 Times in 308 Posts
|
Sbc pushrod question
350 Stocker Engine, Hydraulic Roller, Roller Rockers, Lifters have
.050-.060 plunge. Max RPM 6800. Question: Will there be a measureable difference between 5/16 .080 wall pushrods vs. 3/8 .120 wall pushrods? I am getting pulled different ways depending on the source. Thanks in advance guys. J.R. |
|
|
|
12-15-2014, 07:00 PM
|
#2 |
|
Senior Member
Join Date: Aug 2006
Location: Pukwana SD
Posts: 860
Likes: 554
Liked 99 Times in 49 Posts
|
Re: Sbc pushrod question
Can,t go wrong with the heavier pushrods, but if you not run any spring pressure you can likely get buy with the 5/16 80 wall. You mite ck your lift with one then ck it with the other, if it the same run the 5/16.
|
|
|
|
12-15-2014, 09:08 PM
|
#3 |
|
Member
Join Date: Oct 2002
Location: PORT ORANGE FL
Posts: 285
Likes: 417
Liked 131 Times in 24 Posts
|
Re: Sbc pushrod question
JR check out my website stewardperformance.com
__________________
Denny Steward GT/JA 246 |
|
|
|
|
12-15-2014, 09:19 PM
|
#4 |
|
Veteran Member
Join Date: Mar 2002
Location: Miles From Nowhere
Posts: 7,833
Likes: 2,928
Liked 5,147 Times in 1,964 Posts
|
Re: Sbc pushrod question
Denny, Do you feel a custom 5/16 push rod is a adequate for a high rpm SBC Stocker?
(200 / 400 # springs)
__________________
"We are lucky we don't get as much Government as we pay for." Will Rogers |
|
|
|
|
12-16-2014, 10:00 AM
|
#5 |
|
Member
Join Date: Oct 2002
Location: PORT ORANGE FL
Posts: 285
Likes: 417
Liked 131 Times in 24 Posts
|
Re: Sbc pushrod question
Mark, a 5/16 .120 wall would be the least I would use on a SBC stocker engine.
__________________
Denny Steward GT/JA 246 |
|
|
|
|
12-16-2014, 01:40 PM
|
#6 | |
|
Veteran Member
Join Date: Mar 2002
Location: Miles From Nowhere
Posts: 7,833
Likes: 2,928
Liked 5,147 Times in 1,964 Posts
|
Re: Sbc pushrod question
Quote:
Next question (s) Sounds like about a.070 oil passage ..Enough for roller rockers? Anybody go less? Possible?
__________________
"We are lucky we don't get as much Government as we pay for." Will Rogers |
|
|
|
|
|
12-16-2014, 01:49 PM
|
#7 | |
|
VIP Member
Join Date: Dec 2001
Location: Arkansas - In the middle of everything.
Posts: 2,002
Likes: 64
Liked 783 Times in 195 Posts
|
Re: Sbc pushrod question
Quote:
|
|
|
|
|
|
12-16-2014, 02:04 PM
|
#8 | |
|
Veteran Member
Join Date: Mar 2002
Location: Miles From Nowhere
Posts: 7,833
Likes: 2,928
Liked 5,147 Times in 1,964 Posts
|
Re: Sbc pushrod question
Quote:
Any experience without the coating? I would assume you have to cool the springs to a certain degree too. I also assume there's a fine mist of oil everywhere in there at higher rpm.
__________________
"We are lucky we don't get as much Government as we pay for." Will Rogers |
|
|
|
|
|
12-16-2014, 02:16 PM
|
#9 |
|
VIP Member
Join Date: Mar 2007
Posts: 2,466
Likes: 623
Liked 1,958 Times in 593 Posts
|
Re: Sbc pushrod question
I wouldn't think you would have any problem at all running a good quality 5/16 pushrods with that spring pressure. I ran them on my super stock engines for years with much higher pressure with no failures. Just got some 7/16 for the engine I am puting in my car. It will be interesting to see if there is any difference from the 3/8 that I have been running. I have mostly used comp pushrods in the past.
__________________
Mike Pearson 2485 SS |
|
|
|
|
12-16-2014, 02:31 PM
|
#10 |
|
Member
Join Date: Oct 2002
Location: PORT ORANGE FL
Posts: 285
Likes: 417
Liked 131 Times in 24 Posts
|
Re: Sbc pushrod question
They will work just fine without coatings I have plenty of racers using them now with zero troubles at all.
__________________
Denny Steward GT/JA 246 |
|
|
|
 |
|
|
Linear Mode
