stocker cylinder heads

Alan Roehrich · 12-16-2012, 07:58 PM

Bub, you could be right, but I offered to show them the valve seat cutter from Newen.

Wade_Owens · 12-17-2012, 12:33 PM

You know, I saw this post when it first appeared. I wrote a long, detailed response to what I knew was correct, and what wasnt, pointing out the potential pitfalls. I deleted the post because it just doesnt matter. If you run Stock, take your heads to YOUR techman, have them inspected. Race and set a record in YOUR division. Your life will be much happier.

Wade

Tom Moock · 12-17-2012, 05:27 PM

Wrong information

R. Thorne · 12-17-2012, 10:40 PM

Thanks to all who responded. Ron.

Tim olson · 12-17-2012, 11:11 PM

Wade you are 100% correct , been there done that !

Mike Taylor 3601 · 12-18-2012, 10:00 AM

Alan,
You are talking about newen cnc guide& seat machine,that makes all cuts with one insert correct, that or cutting radius on bottom of seat before installing is only way I know to have seat radiused on lower side of seat to bowl area.
When you say radius seat you are talking about seat that is radiused below where valve seats so that it creates a venturi,just making sure we are talking about same thing.

Do you know anyone with Newen cnc guide&seat machine ,watched those videos lots of times,just curious how they are in the real world? Have'nt went to any trade shows for 8 years went every year from Nashville PRI till last at Indy kinda was burnt out on them,may go to Indy PRI next year.

Mike Taylor 3601

12-16-2012, 07:58 PM	#1
Alan Roehrich Veteran Member Join Date: May 2006 Location: Murfreesboro TN Posts: 5,123 Likes: 1,580 Liked 1,864 Times in 422 Posts	Re: stocker cylinder heads Bub, you could be right, but I offered to show them the valve seat cutter from Newen. __________________ Alan Roehrich 212A G/S

12-17-2012, 12:33 PM	#2
Wade_Owens Senior Member Join Date: Jul 2007 Posts: 578 Likes: 0 Liked 3 Times in 1 Post	Re: stocker cylinder heads You know, I saw this post when it first appeared. I wrote a long, detailed response to what I knew was correct, and what wasnt, pointing out the potential pitfalls. I deleted the post because it just doesnt matter. If you run Stock, take your heads to YOUR techman, have them inspected. Race and set a record in YOUR division. Your life will be much happier. Wade

12-17-2012, 05:27 PM	#3
Tom Moock Senior Member Join Date: May 2004 Posts: 801 Likes: 1 Liked 10 Times in 6 Posts	Re: stocker cylinder heads Wrong information __________________ Tom Moock 5704 STK Last edited by Tom Moock; 12-17-2012 at 06:37 PM. Reason: Post wrong information

12-17-2012, 10:40 PM	#4
R. Thorne Member Join Date: May 2009 Posts: 183 Likes: 69 Liked 101 Times in 34 Posts	Re: stocker cylinder heads Thanks to all who responded. Ron.

12-17-2012, 11:11 PM	#5
Tim olson Junior Member Join Date: Jul 2010 Posts: 20 Likes: 0 Liked 0 Times in 0 Posts	Re: stocker cylinder heads Wade you are 100% correct , been there done that !

12-18-2012, 10:00 AM	#6
Mike Taylor 3601 VIP Member Join Date: Oct 2008 Location: Somerset,Ky Posts: 1,372 Likes: 358 Liked 308 Times in 103 Posts	Re: stocker cylinder heads Alan, You are talking about newen cnc guide& seat machine,that makes all cuts with one insert correct, that or cutting radius on bottom of seat before installing is only way I know to have seat radiused on lower side of seat to bowl area. When you say radius seat you are talking about seat that is radiused below where valve seats so that it creates a venturi,just making sure we are talking about same thing. Do you know anyone with Newen cnc guide&seat machine ,watched those videos lots of times,just curious how they are in the real world? Have'nt went to any trade shows for 8 years went every year from Nashville PRI till last at Indy kinda was burnt out on them,may go to Indy PRI next year. Mike Taylor 3601

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode