|
|
|
|
07-30-2014, 08:21 PM
|
#1 |
|
VIP Member
Join Date: Oct 2008
Location: Somerset,Ky
Posts: 1,377
Likes: 365
Liked 313 Times in 106 Posts
|
Re: wont rev
have msd chip rev limiter take chip out,they will rev in water and shut off under load if bad.
Mike Taylor 3601 |
|
|
|
07-30-2014, 09:01 PM
|
#2 |
|
Junior Member
Join Date: Jul 2014
Location: oklahoma
Posts: 33
Likes: 0
Liked 0 Times in 0 Posts
|
Re: wont rev
i don't have msd i have a hei only, the fuel pressure Gage never drops below 5 psi, do i need a msd?
|
|
|
|
|
07-30-2014, 09:57 PM
|
#3 |
|
Junior Member
Join Date: Jun 2014
Posts: 43
Likes: 0
Liked 0 Times in 0 Posts
|
Re: wont rev
Also disconnect tach.
Change the HEI cap and rotor also, any HEI will work your just testing to see if it runs fine, if it dose you can repair or replace yours then, but that take the whole dist. out loop completely. No you don't need a msd if it ran before it'll run again (I don't need no stinking msd). Last edited by bigfoot584; 07-30-2014 at 10:06 PM. |
|
|
|
|
07-30-2014, 10:02 PM
|
#4 |
|
Junior Member
Join Date: Jul 2014
Location: oklahoma
Posts: 33
Likes: 0
Liked 0 Times in 0 Posts
|
Re: wont rev
thankx i will
|
|
|
|
|
08-06-2014, 07:45 PM
|
#5 |
|
Junior Member
Join Date: Jan 2013
Posts: 2
Likes: 0
Liked 0 Times in 0 Posts
|
Re: wont rev
Had a similer problem,would only go 5000 in 1st gear,ok in 2nd and 3rd.changed pump,regulator,filter,cap,rotor and unhooked the tach(not all at once lol) changed the hei control module and it works perfect
|
|
|
|
|
08-07-2014, 08:05 AM
|
#6 |
|
Member
Join Date: Nov 2001
Location: manville nj
Posts: 359
Likes: 198
Liked 13 Times in 10 Posts
|
Re: wont rev
try 7 lbs. fuel pressure
|
|
|
|
|
08-07-2014, 09:19 AM
|
#7 |
|
Guest
Posts: n/a
|
Re: wont rev
Need to look at that HEI module. I had one in a car I was trying to sell. It ran me through the ringer. I bought and tried 3 different modules before I bought an MSD replacement, and that fixed it. If you know somebody with a distributor machine you might want to take it there and have it checked out for yourself. I've heard GM had different part numbers for modules, and the ones that came in the HP cars were the ones to use.
|
|
|
|
08-08-2014, 01:34 PM
|
#8 | |
|
Veteran Member
Join Date: Mar 2002
Location: Miles From Nowhere
Posts: 7,836
Likes: 2,928
Liked 5,147 Times in 1,964 Posts
|
Re: wont rev
Quote:
I would install (minimum) a 6A , Blaster coil outside the cap and away from heat, and a new pick up coil for insurance. Eliminate the trouble sources. You're only talking about maybe 300 bucks (American)
__________________
"We are lucky we don't get as much Government as we pay for." Will Rogers |
|
|
|
|
|
08-08-2014, 02:40 PM
|
#9 |
|
Senior Member
Join Date: May 2004
Location: Brookfield, CT
Posts: 708
Likes: 13
Liked 319 Times in 68 Posts
|
Re: wont rev
What Mark said, HEI in a stocker. You,ve got to be kidding.
__________________
Lee Valentine 1661 STK |
|
|
|
|
08-08-2014, 11:56 PM
|
#10 | |
|
VIP Member
Join Date: Sep 2002
Location: Tacoma, Washington
Posts: 1,632
Likes: 0
Liked 5 Times in 5 Posts
|
Re: wont rev
Quote:
Danny Durham |
|
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
