Tow truck tranny issues, back again

[Steve Grady]

Have you checked it for any trouble codes or checked the line pressure?

[Jeff Stout]

I know mine is a powerstroke, but brake lights would vibrate off and on and made it stay in low. Don't know why but it fixed it. Things I tried wireless throttle cable gas pedal, 3 pack solenoids, converter The fix was brake light switch and adjusted solved it.

[BTR69]

Originally Posted by Jeff Stout

I know mine is a powerstroke, but brake lights would vibrate off and on and made it stay in low. Don't know why but it fixed it. Things I tried wireless throttle cable gas pedal, 3 pack solenoids, converter The fix was brake light switch and adjusted solved it.

Thanks for the info. I'll definitely change it out. Those aren't so expensive that I can't pay for one and hurt me if it's not the fix.

[Kirk Morgan]

As a last thing to do you could get a stand alone controller for the transmission.

[BTR69]

Originally Posted by Kirk Morgan

As a last thing to do you could get a stand alone controller for the transmission.

Thanks. I've heard about this recently, but don't know anything about them. I'll be googling it tonight.. Haven't been able to make time for the truck recently. Tomorrow is looking good for me getting time to get back on it. Going to check out the speed sensor on the case that missed earlier on.

[Alan Roehrich]

Originally Posted by BTR69

Thanks. I've heard about this recently, but don't know anything about them. I'll be googling it tonight.. Haven't been able to make time for the truck recently. Tomorrow is looking good for me getting time to get back on it. Going to check out the speed sensor on the case that missed earlier on.

Why was it rebuilt to begin with?


Those are pretty reliable, I don't seem to have too much trouble with them. But then they get the Sonnax fixes, the Alto frictions, and a Superior valve body kit. That tends to eliminate further problems.


Order yourself the ATSG manual for the 4L80E. If you're going to work on it, you'll find that to be indispensable.

[BTR69]

Originally Posted by Alan Roehrich

Why was it rebuilt to begin with?


Those are pretty reliable, I don't seem to have too much trouble with them. But then they get the Sonnax fixes, the Alto frictions, and a Superior valve body kit. That tends to eliminate further problems.


Order yourself the ATSG manual for the 4L80E. If you're going to work on it, you'll find that to be indispensable.

After swapping out several parts that "could" cause it to go through 1-2 shift, then on 2-3 shift, it still falls back to low gear. Tranny shop I took it to has taken good care of me in the past and has a great reputation around here. The only thing left that they came up with was a rebuild. They did find a couple of internal issues that would end up causing me more grief and fixed those. I remember one having to do with a part that had been machined with too much tolerance from a prior rebuild. I'm taking their word on that. I know they upgraded it with the Sonnax parts. They kept it for a while troubleshooting and feel the ECU may be the problem. If I can find one in the junkyard, I may grab it, but have been told I'll likely need it flashed. The only other things that I can think of that haven't been changed out are the input speed sensor and neutral safety switch. Unless they did those and I'm not aware of it. Swapping those out tomorrow. If it doesn't work out, I'll look into the stand alone tranny controller. Looked them up this evening and seems like a viable option.

[BTR69]

Originally Posted by Steve Grady

Have you checked it for any trouble codes or checked the line pressure?

The tranny shop ran the codes several times. I don't remember what they were though. I'll see if it's on the paperwork they gave me with it. may take a few days to find that though. They drove it around while hooked up and saw voltage fluctuating pretty badly. New alternator fixed that. Was hoping that was causing the solenoids to fail. Apparently not. They're a reputable shop locally, so I'm hoping the line pressures are where they should be.

I don't remember finding any info on the speed sensor at the front of the case that you mention. I'll look for that, hopefully this weekend.

Thanks..