|
![]() |
#1 |
Junior Member
Join Date: Feb 2023
Posts: 6
Likes: 0
Liked 0 Times in 0 Posts
|
![]()
I have a bracket car with a Jerico that I drive on the street. I know most of you have dedicated race cars but probably the most amount of manual transmission experience out of any drag racing class. So I was hoping to ask if anyone experiences release issues after your drivetrain gets good and heated after driving an hour or so? It's a mild grind and can be stopped easily by easing into gear. I also hold the clutch in for five seconds or more to let everything spin down. When I had the Jerico pilot bearing it would grind so bad I had to turn the car off and then put into gear. I currently run a GM bronze bushing and its night and day improvement. My bellhousing is aligned to perfection both parallelism and concentric. I don't believe it to be an air gap issue either. I'm thinking that it takes so little power to turn these transmission that my pilot shaft may be dragging.
|
![]() |
![]() |
![]() |
#2 |
VIP Member
Join Date: Mar 2007
Posts: 2,330
Likes: 548
Liked 1,656 Times in 507 Posts
|
![]()
usually that is a sign of the clutch dragging a bit. check and make sure the disc slides easily on the input splines. Maybe a bit more air gap
__________________
Mike Pearson 2485 SS |
![]() |
![]() |
![]() |
#3 |
Senior Member
Join Date: May 2007
Location: DRAGSTRIP
Posts: 810
Likes: 641
Liked 478 Times in 139 Posts
|
![]()
Sounds pretty normal to me. Thats just the way all of mine have been. I'm sure the clutch isn't disengaging all the way ,but I just dealt with it.
__________________
5664 AA/SA 1970 NOVA |
![]() |
![]() |
![]() |
#4 |
VIP Member
Join Date: Dec 2001
Location: Texarkana Ark/TX
Posts: 2,363
Likes: 453
Liked 693 Times in 269 Posts
|
![]()
Pilot bushing could be dry and dragging or too shallow and catching on the input shaft. It is normal to grind if the clutch air gap is not wide. I used to put in low gear, use syncro's to stop clutch and transmission insides from spinning and then go to reverse.
__________________
Adger Smith (Former SS) |
![]() |
![]() |
![]() |
#5 |
VIP Member
Join Date: Jun 2007
Location: from Vancouver BC Canada, now in Nova Scotia
Posts: 1,259
Likes: 246
Liked 949 Times in 262 Posts
|
![]()
What type of clutch are you using? A bronze pilot bushing will not last very long with a sintered iron disc, like a McLeod Soft Lok. The dust from the clutch disc is abrasive, and will chew up that bronze bushing pretty quick, and allow the input shaft to wobble around.
__________________
NHRA 6390 STK M/S 85 Mustang |
![]() |
![]() |
Liked |
![]() |
#6 |
Junior Member
Join Date: Feb 2023
Posts: 6
Likes: 0
Liked 0 Times in 0 Posts
|
![]() |
![]() |
![]() |
![]() |
#7 |
Junior Member
Join Date: Feb 2023
Posts: 6
Likes: 0
Liked 0 Times in 0 Posts
|
![]()
Thanks for the feedback, yea I dealt with it with my last combo for ten plus years. This combo is much better. I think removing the Jerico pilot bearing and going back to a bronze bushing made the difference. Sounds like it's pretty common.
|
![]() |
![]() |
![]() |
#8 | |
Junior Member
Join Date: Feb 2023
Posts: 6
Likes: 0
Liked 0 Times in 0 Posts
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#9 | |
Junior Member
Join Date: Feb 2023
Posts: 6
Likes: 0
Liked 0 Times in 0 Posts
|
![]() Quote:
Last edited by Weekiman; 02-23-2023 at 06:57 AM. |
|
![]() |
![]() |
![]() |
#10 |
VIP Member
Join Date: Dec 2001
Location: Texarkana Ark/TX
Posts: 2,363
Likes: 453
Liked 693 Times in 269 Posts
|
![]()
I know this is Hijacking the thread, But...I think the OP has his answer.
Has anyone used a 10,000 RPM brand multi disc metallic clutch with diaphragm? Looks like you shim the stand height to get it set up. (no instructions) I have a new one that came to me as a spare when I bought all of a buddies racecar Estate. Is it something usable or just old junk?
__________________
Adger Smith (Former SS) |
![]() |
![]() |
![]() |
|
|