Some "Dime Rockets" for the 4TH! - Page 49

Billy Nees · 03-09-2022, 09:46 AM

It should probably run pretty good. The 60* V6 has been done before (right Yac?). I don't know what transaxle you would use (125?) and I'm not sure what 4 speed transaxle came in it. It's an OBD1 car so you would probably wind up putting in an aftermarket ECU to tune it but there are some older ones popping up used.
You're off on your weight because NHRA did away with the 17.5 lb. class so you would wind up in BF at 2650 (doubtful) or the new CF at 3115.
I know that there's an older Grand Am running around D1 that's real fast but I think it's a Buick motor.

Mark Yacavone · 03-09-2022, 12:54 PM

Quote:

Originally Posted by mike britt

Any body ever look into building a 95 Grand Am with the V-6. 201 cubic inches and a pretty good size throttle body, .409 lift cam, fairly good compression, 15.15 index, seems like it wouldn't be too hard to get that thing under the index. Rated at 150 hp and around 2700 pounds.

It wouldn't be too hard to get one under the index.
Actually it's .430 lift in FWD...Comp has the blanks and can make you one with street and strip lobes @ .430 lift. Original duration is about 196 @ .050.
Now, if you want to go fast, it will take some serious hands on fabrication.
Earlier non-electric T 440 should bolt in.
3 speed 125 requires fabbed mounts and a custom right hand axle shaft. Same 245 mm converter, either way.
Log type manifolds are junk. Real headers will take another serious hands- on effort.
Now you'll end up with a fair amount of torque in a FWD car. The car will need a major
weight re-distribution to make it consistent.
I would seriously think about a slower class V 8 or V6 2 bbl. car, instead of this one.

(PS..it's rated at 155 hp)

mike britt · 03-09-2022, 04:35 PM

It's sitting in my yard so I was just looking at it. Probably should've done that one instead of the IROC I did.

mike britt · 03-09-2022, 04:38 PM

Mark, do you think those primaries are long enough?

Mark Yacavone · 03-09-2022, 05:50 PM

Quote:

Originally Posted by mike britt

Mark, do you think those primaries are long enough?

Yup.. The length was dictated by the need to get it out the front header well.
The rear was just a match, dimensionally.
I guess it didn't hurt it .It run 1.05 under on the first full pass ;-)

Mark Yacavone · 03-20-2022, 10:42 PM

1986 C10 , 800 Q jet , .430 cam, 190 hp! You guys can finish the equation ;-)

Billy Nees · 03-21-2022, 07:22 AM

Quote:

Originally Posted by Mark Yacavone

1986 C10 , 800 Q jet , .430 cam, 190 hp! You guys can finish the equation ;-)

Definitely COULD qualify as a "Dime Rocket"!
It also goes to show that the people running this"$#1T Show" don't know cars or combos.

Larry Hill · 03-21-2022, 07:50 AM

After all of these years I have a “Dime Rocket “?

Billy Nees · 03-21-2022, 08:44 AM

Quote:

Originally Posted by Larry Hill

After all of these years I have a “Dime Rocket “?

If you say so, I'll take your word for it!

89bird · 10-17-2022, 03:03 AM

I recently seen a local guy racing a basically all stock 97 camaro with a lt1 auto combo, from what he tells me it has some suspension upgrades which he bought all used and he paid 1500 for the car because a blow head gasket. Not the fastest but consistent, and definitely under 5 grand the only weak point on the car is the rearend he says.

03-09-2022, 09:46 AM	#481
Billy Nees VIP Member Join Date: Oct 2002 Location: On a hilltop in Pa. Posts: 4,278 Likes: 3,181 Liked 6,957 Times in 1,569 Posts	Re: Some "Dime Rockets" for the 4TH! It should probably run pretty good. The 60* V6 has been done before (right Yac?). I don't know what transaxle you would use (125?) and I'm not sure what 4 speed transaxle came in it. It's an OBD1 car so you would probably wind up putting in an aftermarket ECU to tune it but there are some older ones popping up used. You're off on your weight because NHRA did away with the 17.5 lb. class so you would wind up in BF at 2650 (doubtful) or the new CF at 3115. I know that there's an older Grand Am running around D1 that's real fast but I think it's a Buick motor. __________________ Billy Nees 1188 STK, SS Reality, what a concept!

03-09-2022, 04:35 PM	#483
mike britt Member Join Date: Mar 2013 Location: Italy, Texas Posts: 142 Likes: 216 Liked 43 Times in 19 Posts	Re: Some "Dime Rockets" for the 4TH! It's sitting in my yard so I was just looking at it. Probably should've done that one instead of the IROC I did.

03-09-2022, 04:38 PM	#484
mike britt Member Join Date: Mar 2013 Location: Italy, Texas Posts: 142 Likes: 216 Liked 43 Times in 19 Posts	Re: Some "Dime Rockets" for the 4TH! Mark, do you think those primaries are long enough?

03-20-2022, 10:42 PM	#486
Mark Yacavone Veteran Member Join Date: Mar 2002 Location: Miles From Nowhere Posts: 7,474 Likes: 2,650 Liked 4,573 Times in 1,733 Posts	Re: Some "Dime Rockets" for the 4TH! 1986 C10 , 800 Q jet , .430 cam, 190 hp! You guys can finish the equation ;-) __________________ We are lucky we don't get as much Government as we pay for..... Will Rogers

03-21-2022, 07:50 AM	#488
Larry Hill Live Reporter Join Date: Oct 2004 Location: Hickory, Ky Posts: 10,315 Likes: 1,671 Liked 9,553 Times in 1,983 Posts	Re: Some "Dime Rockets" for the 4TH! After all of these years I have a “Dime Rocket “? __________________ IHM Used Parts https://ihmusedparts.com 888-821-1817

10-17-2022, 03:03 AM	#490
89bird Junior Member Join Date: Aug 2013 Location: hamburg ny Posts: 38 Likes: 255 Liked 1 Time in 1 Post	Re: Some "Dime Rockets" for the 4TH! I recently seen a local guy racing a basically all stock 97 camaro with a lt1 auto combo, from what he tells me it has some suspension upgrades which he bought all used and he paid 1500 for the car because a blow head gasket. Not the fastest but consistent, and definitely under 5 grand the only weak point on the car is the rearend he says.