1964 Dodge 330 "Race Hemi"

Tom Nolan · 07-10-2013, 05:46 PM

Dash @ autobody shop. Filled several drilled/screw holes from 49 years of gauges and tach's. Smoothed and sanded several shaker can paint jobs off. Paint tomorrow for dash and all interior trim pieces! Racer red! Should be better than new.

Tom Nolan · 07-12-2013, 10:12 AM

Painted Dash
Next Stop......Chrome Moly Cage! Note the holes in the dash for bars to pass thru.

Bob Pagano · 07-12-2013, 05:11 PM

The Tynman page is ancient history.

Dyno · 07-12-2013, 05:53 PM

I know of a complete aluminum front group for sale for a 64 Dodge. The front fenders are NOS. Send me a PM for the phone number. Dyno

MWNorris · 07-14-2013, 07:44 AM

Quote:

Originally Posted by Bob Pagano

The Tynman page is ancient history.

what happen? I talked to him just a few months ago...

jimi · 07-12-2013, 08:08 PM

not trying to hijack the thread but here is mine. engine is finally done,hopefully It will be in the car by next week.

340Cuda · 07-13-2013, 11:38 AM

Quote:

Originally Posted by jimi

not trying to hijack the thread but here is mine. engine is finally done,hopefully It will be in the car by next week.

Drooling over both these cars!

Tom Nolan · 07-25-2013, 01:45 PM

I ordered Schumacher motor mounts, installed them on the plastic block, slotted the mounts welded to the K member. However something is messed up.......block sits crooked? Any advice?

Mark Madison · 07-25-2013, 03:31 PM

Quote:

Originally Posted by Tom Nolan

I ordered Schumacher motor mounts, installed them on the plastic block, slotted the mounts welded to the K member. However something is messed up.......block sits crooked? Any advice?

Do Not use the Schumacher Hemi to wedge conversion mount. They raise all kinds of hell with header clearance. Been there done that, Remember that one A-56? Infact Marks headers will not fit using that mount system.They are good to locate the engine placement, like Mark said the engine is skewed to the passenger side.There is a guy in Wisconson who makes the 64/65 Hemi K-members I was able to talk him into selling just the mounting brackets so I could weld up my K-member

Mark Madison
a/sa7995

Tom Nolan · 07-25-2013, 06:26 PM

So is there anything wrong with putting the engine in square? Once I get the headers up here I will bolt them to the mock up block and make the engine fit straight.....crank center-line in the center, lower maybe....valve covers should come on and off with out any clearance issues?
Legendary Interior just showed up today.......looks fantastic! Crimson red 330 Super-stock pattern. New door seals, and black headliner......oh ya!

07-10-2013, 05:46 PM	#1
Tom Nolan Member Join Date: Dec 2001 Location: Lacombe, Alberta, Canada Posts: 182 Likes: 0 Liked 64 Times in 11 Posts	Re: 1964 Dodge 330 "Race Hemi" Dash @ autobody shop. Filled several drilled/screw holes from 49 years of gauges and tach's. Smoothed and sanded several shaker can paint jobs off. Paint tomorrow for dash and all interior trim pieces! Racer red! Should be better than new. Attached Thumbnails

07-12-2013, 10:12 AM	#2
Tom Nolan Member Join Date: Dec 2001 Location: Lacombe, Alberta, Canada Posts: 182 Likes: 0 Liked 64 Times in 11 Posts	Re: 1964 Dodge 330 "Race Hemi" Painted Dash Next Stop......Chrome Moly Cage! Note the holes in the dash for bars to pass thru. Attached Thumbnails Last edited by Tom Nolan; 07-12-2013 at 04:48 PM. Reason: spelling

07-12-2013, 05:11 PM	#3
Bob Pagano VIP Member Join Date: Jun 2002 Location: New Holland, PA Mooresville,NC Posts: 1,163 Likes: 243 Liked 16 Times in 11 Posts	Re: 1964 Dodge 330 "Race Hemi" The Tynman page is ancient history. __________________ Bob Pagano A/SA

07-12-2013, 05:53 PM	#4
Dyno Senior Member Join Date: Dec 2002 Posts: 919 Likes: 1,147 Liked 693 Times in 205 Posts	Re: 1964 Dodge 330 "Race Hemi" I know of a complete aluminum front group for sale for a 64 Dodge. The front fenders are NOS. Send me a PM for the phone number. Dyno

07-12-2013, 08:08 PM	#6
jimi Member Join Date: Mar 2002 Location: usa Posts: 239 Likes: 7 Liked 21 Times in 8 Posts	Re: 1964 Dodge 330 "Race Hemi" not trying to hijack the thread but here is mine. engine is finally done,hopefully It will be in the car by next week. Attached Thumbnails Last edited by jimi; 07-12-2013 at 08:13 PM. Reason: pic did not attach

07-25-2013, 01:45 PM	#8
Tom Nolan Member Join Date: Dec 2001 Location: Lacombe, Alberta, Canada Posts: 182 Likes: 0 Liked 64 Times in 11 Posts	Re: 1964 Dodge 330 "Race Hemi" I ordered Schumacher motor mounts, installed them on the plastic block, slotted the mounts welded to the K member. However something is messed up.......block sits crooked? Any advice?

07-25-2013, 06:26 PM	#10
Tom Nolan Member Join Date: Dec 2001 Location: Lacombe, Alberta, Canada Posts: 182 Likes: 0 Liked 64 Times in 11 Posts	Re: 1964 Dodge 330 "Race Hemi" So is there anything wrong with putting the engine in square? Once I get the headers up here I will bolt them to the mock up block and make the engine fit straight.....crank center-line in the center, lower maybe....valve covers should come on and off with out any clearance issues? Legendary Interior just showed up today.......looks fantastic! Crimson red 330 Super-stock pattern. New door seals, and black headliner......oh ya! Attached Thumbnails

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode