Dyno numbers 305

philbilly · 01-13-2014, 10:05 PM

Quote:

Originally Posted by nolongerracing

May have to wait about 6 weeks? That's what I've been told.

I was told 4 weeks. But for 200 I can get in 2 weeks. 300 I can have in 1 week. I am doing some negotiating cause I ain't waitin till February for pistons.

Dean Feiock · 01-15-2014, 12:21 AM

Quote:

Originally Posted by philbilly

I was told 4 weeks. But for 200 I can get in 2 weeks. 300 I can have in 1 week. I am doing some negotiating cause I ain't waitin till February for pistons.

Yes, CP is a good choice.

But if you are not putting them in a properly prepped Bowtie block or a properly prepped/sleeved 350/307 block, you aren't going to find the power you are looking for.

Unless you have a rock solid stable cylinder wall, with the right finish, no piston or ring package will help you.

Also consider calling Total Seal for your ring package. If you are used to buying a $50 ring set, then prepare yourself before you call. Good ring packages can be ten times that amount.

James Perrone · 01-15-2014, 10:34 AM

why CP over everything else? I have them are they that much better than the others?

philbilly · 01-15-2014, 12:23 PM

Quote:

Originally Posted by James Perrone

why CP over everything else? I have them are they that much better than the others?

I can tell you what made my mind up. Cp seemed smarter than the other companies. They knew what I was looking for.

philbilly · 02-27-2014, 09:27 PM

Quote:

Originally Posted by philbilly

I can tell you what made my mind up. Cp seemed smarter than the other companies. They knew what I was looking for.

I was told 4 week wait on pistons still havent gotten them. I am not very happy with this co. I wanted to race south georgia...

philbilly · 03-03-2014, 10:46 PM

Pistons arrived today from cp. I ran rotating assembly over to Terry Smith and got the final balance. We got about all the rings ready. Block is prepped and ready. Looks like I might make South Georgia.
If I have enough time I am going to run it on the dyno. I may have to settle with a few laps up the road! I will dyno when I get in from the gators.

Kenny Wigington · 03-03-2014, 11:51 PM

Good luck Phil ! I wish I could be there @ sgmp too !

01-15-2014, 10:34 AM	#3
James Perrone VIP Member Join Date: Feb 2004 Location: LONG ISLAND N.Y. Posts: 1,698 Likes: 3,455 Liked 1,865 Times in 435 Posts	Re: Dyno numbers 305 why CP over everything else? I have them are they that much better than the others? __________________ james perrone 1290 STK

03-03-2014, 10:46 PM	#6
philbilly Member Join Date: Aug 2011 Location: Demossville,KY Posts: 337 Likes: 0 Liked 0 Times in 0 Posts	Re: Dyno numbers 305 Pistons arrived today from cp. I ran rotating assembly over to Terry Smith and got the final balance. We got about all the rings ready. Block is prepped and ready. Looks like I might make South Georgia. If I have enough time I am going to run it on the dyno. I may have to settle with a few laps up the road! I will dyno when I get in from the gators.

03-03-2014, 11:51 PM	#7
Kenny Wigington Senior Member Join Date: Sep 2004 Location: Cumming,Ga. USA Posts: 967 Likes: 36 Liked 60 Times in 12 Posts	Re: Dyno numbers 305 Good luck Phil ! I wish I could be there @ sgmp too ! __________________ 2894 STK