|
|
|
|
02-29-2024, 01:33 PM
|
#1 |
|
Senior Member
Join Date: Mar 2002
Location: NS CANADA
Posts: 884
Likes: 1,557
Liked 380 Times in 147 Posts
|
Re: U/SA 302 ffffford build
Another piece of the puzzle, new batt box.
Last edited by goinbroke2; 02-29-2024 at 01:47 PM. |
|
|
|
02-29-2024, 07:20 PM
|
#2 |
|
Senior Member
Join Date: Mar 2002
Location: NS CANADA
Posts: 884
Likes: 1,557
Liked 380 Times in 147 Posts
|
Re: U/SA 302 ffffford build
Wife is heavy into off roading with her bronco....now I know why she never said anything when my parts came in, 3hr's later, her traction mats showed up!! Always has to out do me, LOL!
|
|
|
|
| Liked |
|
03-16-2024, 12:28 PM
|
#3 |
|
Senior Member
Join Date: Mar 2002
Location: NS CANADA
Posts: 884
Likes: 1,557
Liked 380 Times in 147 Posts
|
Re: U/SA 302 ffffford build
Got another video almost done.
So far, Removed the two bus batteries as well as the master switch and 20ft of double O wire.(100lb's??) Reinstalled the rear carpet. Got the new battery tray in by removing the fuel pressure reg and some other wiring that was in the way, then had to move the starter solenoid too. Got that done and a quick disconnect on the new "die hard" batt. Working on the fuel system under the hood now. Gotta go pick up some fittings and a tap for fuel checks. Pumped two jerry cans of fuel through the system to flush more of the old crap out. (1/2" line and a holley blue pump empty a tank pretty quick!!) I'll finish the fuel system and then probably post a video of my junk in progress. Pulled off the rear spoiler because they only came on the indy 500 pace cars in 1979 and this is a ghia. Also, went and picked up a water pump drive from fellow class racer Rory McNeil yesterday so that will be next after the fuel system is done. I must be getting lots done, I can tell because the wife is getting really mad with my absence....lol... |
|
|
|
| Liked |
|
03-20-2024, 10:21 AM
|
#4 |
|
Senior Member
Join Date: Mar 2002
Location: NS CANADA
Posts: 884
Likes: 1,557
Liked 380 Times in 147 Posts
|
Re: U/SA 302 ffffford build
Here's part 5 of undoing the bracket car and building a stocker, lol!
|
|
|
|
|
03-26-2024, 02:48 PM
|
#5 |
|
Senior Member
Join Date: Mar 2002
Location: NS CANADA
Posts: 884
Likes: 1,557
Liked 380 Times in 147 Posts
|
Re: U/SA 302 ffffford build
Got the pump drive mounted and I ran a fuseable link and a relay to run it and the electric fan too.
A million little steps.... Too busy working on other stuff, lol. Had to fab up a lever and arm for a stainless steel milking valve. Last edited by goinbroke2; 03-26-2024 at 08:52 PM. |
|
|
|
| Liked |
|
03-28-2024, 12:53 PM
|
#6 |
|
Senior Member
Join Date: Mar 2002
Location: NS CANADA
Posts: 884
Likes: 1,557
Liked 380 Times in 147 Posts
|
Re: U/SA 302 ffffford build
Progress...once again, 1 step ahead and 2 back...
Got the batt all installed...and then looked at the blue 86lx in the driveway....the battery is supposed to be negative first as the front post is quite close to the hood..swap everything around... |
|
|
|
|
03-28-2024, 12:57 PM
|
#7 |
|
Senior Member
Join Date: Mar 2002
Location: NS CANADA
Posts: 884
Likes: 1,557
Liked 380 Times in 147 Posts
|
Re: U/SA 302 ffffford build
Then I found a smaller black cap to replace the big grey ugly one. (from a 75 international 304)
Not a "performance" thing, but it will "look older" lol!! |
|
|
|
 |
|
|
Hybrid Mode
