|
![]() |
#1 |
Junior Member
Join Date: Jul 2010
Posts: 52
Likes: 4
Liked 8 Times in 3 Posts
|
![]()
Whats the best way to get rid of crankcase pressure with out a pan evac system for a small block stocker??
|
![]() |
![]() |
![]() |
#2 |
Member
Join Date: Mar 2013
Location: Italy, Texas
Posts: 176
Likes: 366
Liked 66 Times in 31 Posts
|
![]()
Go get you an electric air injection pump off a toyota or gm and build a scavenge tank with a breather. Cheap and easy and fairly effective.
|
![]() |
![]() |
![]() |
#3 |
VIP Member
Join Date: Oct 2013
Location: Gulf Breeze, FL
Posts: 1,651
Likes: 8
Liked 33 Times in 16 Posts
|
![]()
My low buck solution and legal...
![]()
__________________
Rich Taylor I/SA - 321 |
![]() |
![]() |
![]() |
#4 |
Member
Join Date: Mar 2013
Location: Greentown, IN
Posts: 113
Likes: 0
Liked 0 Times in 0 Posts
|
![]()
The better the engine is sealed up the less Blowby you will have which equals less Crankcase Pressure you will have. If the engine is a wet sump you can measure the Blowby with a good Blowby meter. Low leak down readings do not equal low Blowby.anything over 2cfm is too much.
|
![]() |
![]() |
![]() |
#5 |
VIP Member
Join Date: Nov 2002
Location: Massapequa Park,NY
Posts: 1,281
Likes: 1,892
Liked 969 Times in 307 Posts
|
![]() |
![]() |
![]() |
![]() |
#6 |
VIP Member
Join Date: Oct 2013
Location: Gulf Breeze, FL
Posts: 1,651
Likes: 8
Liked 33 Times in 16 Posts
|
![]()
Just a simple path for pressure to escape.
__________________
Rich Taylor I/SA - 321 |
![]() |
![]() |
![]() |
#7 |
Member
Join Date: Feb 2009
Posts: 244
Likes: 1
Liked 7 Times in 6 Posts
|
![]()
If you have the valve cover connected to the fuel pump block off I don't think you're doing anything. They see the same pressure. I use manifold vacuum through the base of the carb and run a vacuum gauge to measure pan vacuum. It's not great but I do pull about 5 inches at the starting line. That's with both crank seals in the correct way.
|
![]() |
![]() |
![]() |
#8 |
Member
Join Date: Feb 2009
Posts: 244
Likes: 1
Liked 7 Times in 6 Posts
|
![]() |
![]() |
![]() |
![]() |
#9 |
VIP Member
Join Date: Nov 2002
Location: Massapequa Park,NY
Posts: 1,281
Likes: 1,892
Liked 969 Times in 307 Posts
|
![]() |
![]() |
![]() |
![]() |
#10 | |
VIP Member
Join Date: Oct 2013
Location: Gulf Breeze, FL
Posts: 1,651
Likes: 8
Liked 33 Times in 16 Posts
|
![]() Quote:
Btw, the above images do not show that a breather is used on the passenger side cover. No breather/sealed on the driver side. ![]()
__________________
Rich Taylor I/SA - 321 Last edited by HandOverFist; 05-27-2016 at 03:43 PM. Reason: add image |
|
![]() |
![]() |
![]() |
|
|