Bellhousing

[J&S Racing]

Thanks guys.

It really ended up being a no brainer.

The McLeod is 15 pounds lighter, has a larger inspection window, was on the shelf vs. 3/4 week wait and was $100 cheaper.

They currently are shipping with the titanium liner for no extra cost.

[Nmbr1GMfan]

Originally Posted by J&S Racing

Thanks guys.

It really ended up being a no brainer.

The McLeod is 15 pounds lighter, has a larger inspection window, was on the shelf vs. 3/4 week wait and was $100 cheaper.

They currently are shipping with the titanium liner for no extra cost.

I really like that 15 lbs savings. I would also like to know what the fork options are, with Browell there are some great adjustability options.

[JHeath]

I bought the McLeod SBF bellhousing for my 93 Mustang stocker, it is really nice, thinking of using it on my CJ project. I am not sure about the fork, the stock mustang cable will work, haven't really looked at what I will need for mechanical linkage.

[b.guggenmos]

Originally Posted by JHeath

I bought the McLeod SBF bellhousing for my 93 Mustang stocker, it is really nice, thinking of using it on my CJ project. I am not sure about the fork, the stock mustang cable will work, haven't really looked at what I will need for mechanical linkage.

Nice big window. What trans are you running with that bell? I heard the depth is for a T5 and that is different than a Jerico?

[JHeath]

My Jerico is T5 input length

[john lemoine]

hey jerry on another note did you find someone to make you headers on you cobra jet project thanks john lemoine

[Rory McNeil]

Originally Posted by b.guggenmos

Nice big window. What trans are you running with that bell? I heard the depth is for a T5 and that is different than a Jerico?

So is mine Brian. Any SB Ford application using the FOX style cable clutch needs to use the longer T5 input shaft and deeper bellhousing to have enough room for it to all fit. The Jerico for my FE has an input shaft that is about an inch shorter than the one for my small block. You just order the correct input (or trans) from Jerico for your application. That is how both my Jericos came to have the correct length input shafts and tip dimensions for my Fords, but have the MoPar "Hemi" 18 spline configuration, which allows me to use the small input Ford throw out bearing and fork.
Jerry, thats a great looking bellhousing, does McLeod have those in stock for SB Fords? My steel McLeod bell is coming due for a re cert, less weight and a window would sure be nice. Does yours have provision for both the 157 and 164 tooth flywheel and starter?

[JHeath]

I bought it from Jegs, a 164 tooth flywheel will fit. part # is 8560T

[Jim Caughlin]

I run a Quicktime SBF bellhousing, I would guess looking at the picture of the McLeod that they would be comparable in weight. For sure the Lakewood unit is way heavier and also considerably dimensionally larger. In the case of the Quicktime, they only fit the 157 tooth, not the larger 164. Also, Quicktime used to be a pretty good price, after they got bought out, the price virtually doubles, as I recall the SBF unit is around $600. No complaints with the quality though.

Jim Caughlin
SS 6019

[JohnRoderick]

Originally Posted by JHeath

I bought the McLeod SBF bellhousing for my 93 Mustang stocker, it is really nice, thinking of using it on my CJ project. I am not sure about the fork, the stock mustang cable will work, haven't really looked at what I will need for mechanical linkage.

Can you or anyone else that has used this bellhousing comment on how easy it is for you to set the air gap with the inspection window that far back?

Thanks,
John