Moser engineering axles, spool, hardware

flash · 08-23-2021, 08:37 AM

Moser pays at div and nationals,strange only at nationals

Darrel Goheen · 08-23-2021, 11:28 PM

When I needed axles a couple of years ago I believe Strange said it was about a 6 week lead time. Moser sent the axles out the next day at a much lower cost!

Jeff Teuton · 08-25-2021, 05:51 PM

Good People. Fair prices. Couple of years ago I needed a center chunk for one of my drag packs. Got Larry Cummins to call them for me and picked it up in Indy. Just good people. Jeff

Rose Racing · 08-25-2021, 06:39 PM

Just bought a set of axles,Ring and Pinion and other goodies this past year and am very satisfied.

SGSST109E · 08-26-2021, 06:36 AM

Had a Mark Williams spool from my modified eliminator days. They cut the same MW spline on the Moser axles I bought in 1996. 35 spline both still in use today.

Bob Shaw · 08-26-2021, 08:50 PM

If you buy stock size replacement axles they won't pay contingency money They did not tell me that when I bought them.

Race Clean · 08-27-2021, 02:40 PM

Quote:

Originally Posted by SGSST109E

Had a Mark Williams spool
They cut the same MW spline on the Moser axles 35 spline both

I bought Moser axles for a M/W spool,the fit was bad, dont know if it was a misunderstanding or they just didn't grasp or could supply the M/W spline config then.Didn't like the feel when I put them in and decided to bite the bullet and buy M/W.
WHAT A DIFFERENCE. fit,finish,design...I will never opt for anything less now.
That said all axles I have seen (or heard) brake or twist is Strange Axles

Light years ago (40 something) I had Summers Brothers axles(and spool)....I regret selling those now. they actually where ¨M/W standard¨ when I look back..

Hacksaw · 08-27-2021, 03:50 PM

Moser stuff is good, the reason they can ship axles in 1 to 2 days is because they inventory axles at a longer length and then cut to match your order. Strange is better, however I did have an issue with a pair of 35 spline axles after 8 runs. The spines started to twist and after talking to there Tech dept. I was told that Strange Axles have an allowable amount of twist and this is acceptable!! M W is the best, no question.

08-23-2021, 08:37 AM	#1
flash Junior Member Join Date: Apr 2012 Posts: 89 Likes: 1 Liked 6 Times in 5 Posts	Re: Moser engineering axles, spool, hardware Moser pays at div and nationals,strange only at nationals

08-23-2021, 11:28 PM	#2
Darrel Goheen Member Join Date: Jan 2011 Location: Hays, KS Posts: 380 Likes: 226 Liked 70 Times in 31 Posts	Re: Moser engineering axles, spool, hardware When I needed axles a couple of years ago I believe Strange said it was about a 6 week lead time. Moser sent the axles out the next day at a much lower cost! __________________ Darrel Goheen 785-623-7021 Stock Eliminator 585 94 Camaro Z/28 LT1/ET 585 67 Chevelle 427 Tehnician for JustAnswer.com

08-25-2021, 05:51 PM	#3
Jeff Teuton VIP Member Join Date: Jan 2002 Location: Houma, LA Posts: 2,717 Likes: 2 Liked 325 Times in 50 Posts	Re: Moser engineering axles, spool, hardware Good People. Fair prices. Couple of years ago I needed a center chunk for one of my drag packs. Got Larry Cummins to call them for me and picked it up in Indy. Just good people. Jeff __________________ Jeff Teuton 4022 STK

08-25-2021, 06:39 PM	#4
Rose Racing Member Join Date: Jan 2012 Location: Sandusky, Ohio Posts: 353 Likes: 95 Liked 226 Times in 74 Posts	Re: Moser engineering axles, spool, hardware Just bought a set of axles,Ring and Pinion and other goodies this past year and am very satisfied.

08-26-2021, 06:36 AM	#5
SGSST109E Member Join Date: Jun 2007 Location: NJ Posts: 351 Likes: 62 Liked 126 Times in 61 Posts	Re: Moser engineering axles, spool, hardware Had a Mark Williams spool from my modified eliminator days. They cut the same MW spline on the Moser axles I bought in 1996. 35 spline both still in use today.

08-26-2021, 08:50 PM	#6
Bob Shaw Member Join Date: Jan 2002 Location: Sedalia, Mo Posts: 436 Likes: 329 Liked 316 Times in 61 Posts	Re: Moser engineering axles, spool, hardware If you buy stock size replacement axles they won't pay contingency money They did not tell me that when I bought them. __________________ Bob Shaw V/SA 515

08-27-2021, 03:50 PM	#8
Hacksaw Senior Member Join Date: Sep 2016 Posts: 882 Likes: 206 Liked 310 Times in 174 Posts	Re: Moser engineering axles, spool, hardware Moser stuff is good, the reason they can ship axles in 1 to 2 days is because they inventory axles at a longer length and then cut to match your order. Strange is better, however I did have an issue with a pair of 35 spline axles after 8 runs. The spines started to twist and after talking to there Tech dept. I was told that Strange Axles have an allowable amount of twist and this is acceptable!! M W is the best, no question.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode