altenator pulley ratio to crank - Page 2

west coast · 01-02-2011, 11:04 PM

Wade are your pulley numbers backwards or is it just me. I have found pulleys for my crank with ratio of 2.26 and 2.10 for my altenator pulley size. Thanks guy's for the helpjust need to make brackets now.

nwebber · 01-02-2011, 11:08 PM

Is there any benefit to underdriving the alternator?

Tom Goldman · 01-03-2011, 01:19 AM

Wades numbers are right for a Stocker that needs no real alternator output.
carburated Stockers run faster with a fully charged battery and an alternator that is really just along for the ride.

GTX JOHN · 01-03-2011, 04:30 AM

I agree with Tom and Wade.....That how we run all our stockers (Although not the truck we use to tow them Home).

Tom keedle · 01-03-2011, 05:47 AM

Quote:

Originally Posted by Tom Goldman

I tried one on my car when I had a micro v belt system on the car.
Two of them failed ,altho they were OEM units. ... locked up the overunning clutch.
may have been the rpm range , as I was running a small engine at the time and hitting about 8400 in the traps.
The most common application of these pulleys is on diesels ,to help minimize belt screech at shut down. ...They also cut down on belt whip when a automatic tensioner is employed .

i was kinda thinking that might help on gear changes...just a thought.

Bob Bender · 01-03-2011, 10:33 PM

Quote:

Originally Posted by Wade_Owens

x2, I have an east coast alt. also. 3" crank, 5" alt. no issues at all.

Wade O

Me too.......................

west coast · 01-04-2011, 11:52 AM

I should have mention this is a stocker. Wade and Bob are you guys just running off the battery and not running any electricity to the altenator?

GTX JOHN · 01-04-2011, 05:12 PM

We use Denso Alt. and still have 13.8 to 14.2 volts above 2,500 with above ratio.....I like all the voltage I can get with MSD. We are seldom below that RPM even in Pits.

John Irving

Wade_Owens · 01-04-2011, 05:17 PM

Quote:

Originally Posted by west coast

I should have mention this is a stocker. Wade and Bob are you guys just running off the battery and not running any electricity to the altenator?

With my ICE Ignition, he likes to see over 14v. By about 3000-3500 rpm's, I have 14.4

I did have a racepak on for awhile, after peaking at 14.4, it stayed there for the duration of the run.

We do have to have a working alternator, hooked up and charging as per rules.

Wade O

Bob Bender · 01-05-2011, 02:40 AM

Quote:

Originally Posted by west coast

I should have mention this is a stocker. Wade and Bob are you guys just running off the battery and not running any electricity to the altenator?

My alt. turns on at approximately 3000 to 3200 rpms and puts out 14.2 volts.

01-02-2011, 11:04 PM	#11
west coast Senior Member Join Date: Dec 2008 Location: Rainy Washington Posts: 609 Likes: 12 Liked 223 Times in 73 Posts	Re: altenator pulley ratio to crank Wade are your pulley numbers backwards or is it just me. I have found pulleys for my crank with ratio of 2.26 and 2.10 for my altenator pulley size. Thanks guy's for the helpjust need to make brackets now.

01-02-2011, 11:08 PM	#12
nwebber Junior Member Join Date: May 2007 Location: springfield OR Posts: 70 Likes: 1 Liked 39 Times in 5 Posts	Re: altenator pulley ratio to crank Is there any benefit to underdriving the alternator? __________________ Norm Webber

01-03-2011, 01:19 AM	#13
Tom Goldman VIP Member Join Date: Jan 2003 Location: Allentown,PA Posts: 2,475 Likes: 887 Liked 865 Times in 235 Posts	Re: altenator pulley ratio to crank Wades numbers are right for a Stocker that needs no real alternator output. carburated Stockers run faster with a fully charged battery and an alternator that is really just along for the ride. __________________ Tom Goldman 1500 SG , 1506 STK

01-03-2011, 04:30 AM	#14
GTX JOHN VIP Member Join Date: Jun 2009 Location: Boulder City, Nevada 89005 Posts: 2,732 Likes: 2,798 Liked 2,482 Times in 697 Posts	Re: altenator pulley ratio to crank I agree with Tom and Wade.....That how we run all our stockers (Although not the truck we use to tow them Home).

01-04-2011, 11:52 AM	#17
west coast Senior Member Join Date: Dec 2008 Location: Rainy Washington Posts: 609 Likes: 12 Liked 223 Times in 73 Posts	Re: altenator pulley ratio to crank I should have mention this is a stocker. Wade and Bob are you guys just running off the battery and not running any electricity to the altenator?

01-04-2011, 05:12 PM	#18
GTX JOHN VIP Member Join Date: Jun 2009 Location: Boulder City, Nevada 89005 Posts: 2,732 Likes: 2,798 Liked 2,482 Times in 697 Posts	Re: altenator pulley ratio to crank We use Denso Alt. and still have 13.8 to 14.2 volts above 2,500 with above ratio.....I like all the voltage I can get with MSD. We are seldom below that RPM even in Pits. John Irving