Nova chassis question

tj310 · 05-11-2012, 09:08 AM

Since I assume your rollbar is already tech approved adding braces to the rear shouldn't require 6" plates top and bottom. ---Trevor

jmcarter · 05-11-2012, 11:36 AM

If you haven't seen Adam Keir's Nova you should contact him...Ken did a unbelievable job on it....know it's a cage car but lots of ideas there, may be a little over the top if you're looking to just modify what you have.

mat H/SA · 05-11-2012, 03:55 PM

Thanks Tj

Don that is exactly what i need to do haha

Mark if it does that oups i welded the wrong thing !

Nathan Stinson · 05-11-2012, 06:25 PM

http://i142.photobucket.com/albums/r...Picture015.jpg

http://i142.photobucket.com/albums/r...cture002-3.jpg

Couple shots of how mine was done.

henrys57wagon · 05-13-2012, 08:38 PM

Mat, Ross sent me an email with pic's of the trunk bars in our Nova and I can forward the email onto you if you like. I will try and post some pic's if I can figure how to transfer them from the email to here, Henry.

mat H/SA · 05-15-2012, 12:50 PM

Thanks Henry i see just fine

Mike Brogniez · 05-15-2012, 07:51 PM

Quote:

Originally Posted by Nathan Stinson

http://i142.photobucket.com/albums/r...Picture015.jpg

http://i142.photobucket.com/albums/r...cture002-3.jpg

Couple shots of how mine was done.

Nice work.....also like to see the fuel pump ''in the shade''....

05-11-2012, 09:08 AM	#1
tj310 Member Join Date: Sep 2009 Location: Dresden On. Canada Posts: 460 Likes: 0 Liked 0 Times in 0 Posts	Re: Nova chassis question Since I assume your rollbar is already tech approved adding braces to the rear shouldn't require 6" plates top and bottom. ---Trevor

05-11-2012, 11:36 AM	#2
jmcarter VIP Member Join Date: Dec 2008 Location: Richmond Hill GA (and Port Ludlow WA) Posts: 4,299 Likes: 2,390 Liked 3,194 Times in 975 Posts	Re: Nova chassis question If you haven't seen Adam Keir's Nova you should contact him...Ken did a unbelievable job on it....know it's a cage car but lots of ideas there, may be a little over the top if you're looking to just modify what you have. __________________ Jim Carter 2340 Super Stock 2340 SST/2340 Stock Set another place at the table

05-11-2012, 03:55 PM	#3
mat H/SA Member Join Date: Sep 2007 Location: Shefford,Qc Can Posts: 295 Likes: 10 Liked 14 Times in 8 Posts	Re: Nova chassis question Thanks Tj Don that is exactly what i need to do haha Mark if it does that oups i welded the wrong thing !

05-11-2012, 06:25 PM	#4
Nathan Stinson Member Join Date: Aug 2006 Location: Nashville, TN Posts: 114 Likes: 29 Liked 4 Times in 1 Post	Re: Nova chassis question http://i142.photobucket.com/albums/r...Picture015.jpg http://i142.photobucket.com/albums/r...cture002-3.jpg Couple shots of how mine was done.

05-13-2012, 08:38 PM	#5
henrys57wagon Member Join Date: Jan 2009 Location: Carleton Place, On. Canada Posts: 107 Likes: 5 Liked 0 Times in 0 Posts	Re: Nova chassis question Mat, Ross sent me an email with pic's of the trunk bars in our Nova and I can forward the email onto you if you like. I will try and post some pic's if I can figure how to transfer them from the email to here, Henry. Attached Thumbnails __________________ old 1608 stock racer Last edited by henrys57wagon; 05-13-2012 at 10:06 PM.

05-15-2012, 12:50 PM	#6
mat H/SA Member Join Date: Sep 2007 Location: Shefford,Qc Can Posts: 295 Likes: 10 Liked 14 Times in 8 Posts	Re: Nova chassis question Thanks Henry i see just fine