Help with Accel Calmap 6.0

Rich Biebel · 06-24-2013, 07:31 PM

Tom Goldman was familair with Gen 6 Accel units as I recall...

I had a Gen 7 Accel....and they are a lot different....

Woodro used Holley's as many did I think...

A data logger or an A/F data recorder is very helpfull

I had both but used an Innovate LM-1 mostly....and was way off in some areas...mostly low speed part throttle.....wide open down track was not too bad....but consistancy and predictability was not good...in some conditions....

You have a very steep learning curve and it is not fun...but once it is setup right...they work fine...

Signman · 06-25-2013, 09:04 AM

Used this system when first coming out with my stocker.
It's pretty straight forward. Just use common sense.
Newer systems offer more control but the real benefit is faster processor.
You need a data logger in some form. Old Innovate LM-1 will work and are cheap. I have 2 and will sell them.

Data log your run: RPM and O2 at least
Use the log to identify RPM areas which match cells in the fuel map. Average the O2 in that area. Calculate a percentage of change from logged O2 to target O2. Change the value up or down in the corresponding cell in the fuel map.

The best thing to do is find a good tuner with chassis dyno in in your area. Only better if the tuner races the same series you do. Run the car on the dyno, ask questions and run the car. have fun!

John Nechiporchik · 06-25-2013, 10:15 AM

Frank, Thanks for the input . Your process seems simple and logical. I have a data logger and O2 sensors so I can use your approach.
Thanks again.

John

SuperStock 1890 · 06-25-2013, 06:44 PM

John,
Send me an e-mail. I think I can dig up some of my old maps and print them out for you.

Richscaz@hotmail.com

Rich Biebel · 06-25-2013, 07:12 PM

"The best thing to do is find a good tuner with chassis dyno in in your area"
I agree with Frank 100%

Or get the fuel maps offered from the gent that offered to send them to you.....He knows those cars....

Trust me it is not worth wrestling with this.......

You will waste a lot of time and runs....or worse....hurt something in the engine from being too rich or lean....

I thought it can't be that hard......and no it isn't but you will waste a pile of time/runs and money getting there....and with the cost of racing today.... it is well worth paying for someones time to get a good baseline tuneup...

John Nechiporchik · 06-26-2013, 10:27 AM

Quote:

Originally Posted by SuperStock 1890

John,
Send me an e-mail. I think I can dig up some of my old maps and print them out for you.

Richscaz@hotmail.com

Sent you an e-mail this morning.
Thanks!

Signman · 06-26-2013, 11:02 AM

Rich will get you in the ballpark.
A chassis dyno session will make sure the tune is safe for your combination.

06-24-2013, 07:31 PM	#1
Rich Biebel VIP Member Join Date: Jun 2007 Location: Northern New Jersey suburbs Posts: 2,314 Likes: 25 Liked 544 Times in 213 Posts	Re: Help with Accel Calmap 6.0 Tom Goldman was familair with Gen 6 Accel units as I recall... I had a Gen 7 Accel....and they are a lot different.... Woodro used Holley's as many did I think... A data logger or an A/F data recorder is very helpfull I had both but used an Innovate LM-1 mostly....and was way off in some areas...mostly low speed part throttle.....wide open down track was not too bad....but consistancy and predictability was not good...in some conditions.... You have a very steep learning curve and it is not fun...but once it is setup right...they work fine... __________________ Rich Biebel S/C 1479 Stock 147R

06-25-2013, 09:04 AM	#2
Signman Senior Member Join Date: Oct 2003 Location: Lower Slower Delaware Posts: 535 Likes: 22 Liked 269 Times in 99 Posts	Re: Help with Accel Calmap 6.0 Used this system when first coming out with my stocker. It's pretty straight forward. Just use common sense. Newer systems offer more control but the real benefit is faster processor. You need a data logger in some form. Old Innovate LM-1 will work and are cheap. I have 2 and will sell them. Data log your run: RPM and O2 at least Use the log to identify RPM areas which match cells in the fuel map. Average the O2 in that area. Calculate a percentage of change from logged O2 to target O2. Change the value up or down in the corresponding cell in the fuel map. The best thing to do is find a good tuner with chassis dyno in in your area. Only better if the tuner races the same series you do. Run the car on the dyno, ask questions and run the car. have fun! __________________ Frank Ferrucci I/SA 1271 "Be Thankful for the Gifts You are Given"

06-25-2013, 10:15 AM	#3
John Nechiporchik Member Join Date: Mar 2007 Location: Grosse Ile Mi. Posts: 316 Likes: 84 Liked 13 Times in 7 Posts	Re: Help with Accel Calmap 6.0 Frank, Thanks for the input . Your process seems simple and logical. I have a data logger and O2 sensors so I can use your approach. Thanks again. John

06-25-2013, 06:44 PM	#4
SuperStock 1890 Junior Member Join Date: Aug 2005 Posts: 87 Likes: 0 Liked 0 Times in 0 Posts	Re: Help with Accel Calmap 6.0 John, Send me an e-mail. I think I can dig up some of my old maps and print them out for you. Richscaz@hotmail.com __________________ You don't know what you don't know yet.

06-25-2013, 07:12 PM	#5
Rich Biebel VIP Member Join Date: Jun 2007 Location: Northern New Jersey suburbs Posts: 2,314 Likes: 25 Liked 544 Times in 213 Posts	Re: Help with Accel Calmap 6.0 "The best thing to do is find a good tuner with chassis dyno in in your area" I agree with Frank 100% Or get the fuel maps offered from the gent that offered to send them to you.....He knows those cars.... Trust me it is not worth wrestling with this....... You will waste a lot of time and runs....or worse....hurt something in the engine from being too rich or lean.... I thought it can't be that hard......and no it isn't but you will waste a pile of time/runs and money getting there....and with the cost of racing today.... it is well worth paying for someones time to get a good baseline tuneup... __________________ Rich Biebel S/C 1479 Stock 147R

06-26-2013, 11:02 AM	#7
Signman Senior Member Join Date: Oct 2003 Location: Lower Slower Delaware Posts: 535 Likes: 22 Liked 269 Times in 99 Posts	Re: Help with Accel Calmap 6.0 Rich will get you in the ballpark. A chassis dyno session will make sure the tune is safe for your combination. __________________ Frank Ferrucci I/SA 1271 "Be Thankful for the Gifts You are Given"