Edelbrock head accepted for Sbc in S/S ?

Kingpen · 12-19-2014, 12:35 AM

Was looking to see if any changes on my combo and seen where there are 3 or 4 edelbrock heads listed as replacements for sbc s/s.When did this happen ? .......Victor

FireSale · 12-19-2014, 02:19 AM

What year and engine? On my page for the 68 Ford, the accepted Canfield and AFR heads are listed by number at the bottom and Edelbrock by name only. Across the top the Edelbrock head numbers are entered in small type like they were an afterthought or correction.

Are they highlighted in yellow? They do that with changes.

Dale

J.R. Haddad · 12-19-2014, 04:09 AM

Victor, it happened yesterday. J.R.

Dick Butler · 12-19-2014, 10:30 AM

Good for everyone. Sponsors can get involved. Racers can get new easier to find parts. Only problem is an image thing for the "way it was" starting with all original parts. Spectators can identify the brands and support the makers of the parts..

Kingpen · 12-19-2014, 12:04 PM

All i had heard about was the Dart Iron Eagle head being approved,but I'm usually the last to know anyhow......thanks Victor

FireSale · 12-19-2014, 01:51 PM

I see that listing now. Lots of good stuff to stick on a SBC.

Dale

Ernie Neal · 12-19-2014, 03:12 PM

I did a search on all these numbers and found nothing other than 608879 part number. But that number isn't listed with the last digit of 9. When are they (Edelbrock) going to make them?

Ernie Neal
SS 354

Ed Carpenter · 12-19-2014, 04:47 PM

Called and found out 283 not approved to use aftermarket heads. The only head I could find(like Ernie stated) is a 1.94 valve 185cc head. That wont work anyway for a 283 without a ton of work. I was told the other 3 not available yet.

FireSale · 12-20-2014, 01:01 AM

Based on the code used on the stock car classification guide, only engines with "$" (might be a sub section symbol) under the CID can run the newly listed heads. Seems to start with 327s.

Dale

12-19-2014, 12:35 AM	#1
Kingpen Member Join Date: Feb 2006 Location: sooner state Posts: 105 Likes: 3 Liked 64 Times in 22 Posts	Edelbrock head accepted for Sbc in S/S ? Was looking to see if any changes on my combo and seen where there are 3 or 4 edelbrock heads listed as replacements for sbc s/s.When did this happen ? .......Victor

12-19-2014, 02:19 AM	#2
FireSale VIP Member Join Date: Feb 2014 Location: Lakewood Washington Posts: 1,407 Likes: 29 Liked 237 Times in 126 Posts	Re: Edelbrock head accepted for Sbc in S/S ? What year and engine? On my page for the 68 Ford, the accepted Canfield and AFR heads are listed by number at the bottom and Edelbrock by name only. Across the top the Edelbrock head numbers are entered in small type like they were an afterthought or correction. Are they highlighted in yellow? They do that with changes. Dale

12-19-2014, 04:09 AM	#3
J.R. Haddad Senior Member Join Date: Jun 2012 Posts: 773 Likes: 895 Liked 1,427 Times in 301 Posts	Re: Edelbrock head accepted for Sbc in S/S ? Victor, it happened yesterday. J.R.

12-19-2014, 10:30 AM	#4
Dick Butler VIP Member Join Date: Oct 2002 Location: Richmond Indiana Posts: 1,196 Likes: 5 Liked 32 Times in 19 Posts	Re: Edelbrock head accepted for Sbc in S/S ? Good for everyone. Sponsors can get involved. Racers can get new easier to find parts. Only problem is an image thing for the "way it was" starting with all original parts. Spectators can identify the brands and support the makers of the parts..

12-19-2014, 12:04 PM	#5
Kingpen Member Join Date: Feb 2006 Location: sooner state Posts: 105 Likes: 3 Liked 64 Times in 22 Posts	Re: Edelbrock head accepted for Sbc in S/S ? All i had heard about was the Dart Iron Eagle head being approved,but I'm usually the last to know anyhow......thanks Victor

12-19-2014, 01:51 PM	#6
FireSale VIP Member Join Date: Feb 2014 Location: Lakewood Washington Posts: 1,407 Likes: 29 Liked 237 Times in 126 Posts	Re: Edelbrock head accepted for Sbc in S/S ? I see that listing now. Lots of good stuff to stick on a SBC. Dale

12-19-2014, 03:12 PM	#7
Ernie Neal Senior Member Join Date: Feb 2009 Location: Columbus, Indiana Posts: 522 Likes: 160 Liked 305 Times in 74 Posts	Re: Edelbrock head accepted for Sbc in S/S ? I did a search on all these numbers and found nothing other than 608879 part number. But that number isn't listed with the last digit of 9. When are they (Edelbrock) going to make them? Ernie Neal SS 354

12-19-2014, 04:47 PM	#8
Ed Carpenter Live Reporter Join Date: May 2006 Location: Dripping Springs, Tx Posts: 2,709 Likes: 186 Liked 520 Times in 132 Posts	Re: Edelbrock head accepted for Sbc in S/S ? Called and found out 283 not approved to use aftermarket heads. The only head I could find(like Ernie stated) is a 1.94 valve 185cc head. That wont work anyway for a 283 without a ton of work. I was told the other 3 not available yet. __________________ Ed Carpenter 2005 Chevy Cobalt A/SM Race Engine Development

12-20-2014, 01:01 AM	#9
FireSale VIP Member Join Date: Feb 2014 Location: Lakewood Washington Posts: 1,407 Likes: 29 Liked 237 Times in 126 Posts	Re: Edelbrock head accepted for Sbc in S/S ? Based on the code used on the stock car classification guide, only engines with "$" (might be a sub section symbol) under the CID can run the newly listed heads. Seems to start with 327s. Dale