|
|
![]() |
#1 | |
Veteran Member
Join Date: Mar 2002
Location: Miles From Nowhere
Posts: 7,837
Likes: 2,931
Liked 5,148 Times in 1,965 Posts
|
![]() Quote:
Maybe they already hit?
__________________
"We are lucky we don't get as much Government as we pay for." Will Rogers |
|
![]() |
![]() |
![]() |
#2 |
Member
Join Date: Sep 2011
Location: Oklahoma City, OK
Posts: 215
Likes: 3
Liked 7 Times in 5 Posts
|
![]()
i can check stall on the transbrake right? and i can tell you it will go to 4500 easily on the brake because thats where the 2 step is but it drops a ton of rpm inbetween gears. could line pressure or trans being over full cause this type of issue? the fact that it still leaves is what makes me think the sprag is ok. i was considering raising the 2 step to 6500 and seeing where the converter stopped it. could a bad msd box cause this type of problem? the only things that aren't new are the box and plug wires. so they're pretested but 6-7 years old when everything else is relatively new.
|
![]() |
![]() |
![]() |
#3 |
Senior Member
Join Date: Sep 2016
Posts: 887
Likes: 211
Liked 314 Times in 177 Posts
|
![]()
You may have a converter issue, but if you only went 106 MPH you have a problem with power.
|
![]() |
![]() |
![]() |
#4 | |
Veteran Member
Join Date: Mar 2002
Location: Miles From Nowhere
Posts: 7,837
Likes: 2,931
Liked 5,148 Times in 1,965 Posts
|
![]() Quote:
Your interval times are all within reason, as far as being correct. But still seems like it would go faster than that, if the secondaries weren't working at all.
__________________
"We are lucky we don't get as much Government as we pay for." Will Rogers |
|
![]() |
![]() |
![]() |
#5 |
Live Reporter
Join Date: Jan 2011
Location: New Bern, NC
Posts: 3,467
Likes: 146
Liked 3,363 Times in 731 Posts
|
![]()
Maybe a silly suggestion but in situations like this nothing is silly, maybe a couple plugs wires crossed.
And yes the reason I suggested it is because I done it recently and it cost me over a second in the 1/8 mile!
__________________
James Williamson W200 J/SA. SS/JA Last edited by HR9121; 05-16-2017 at 11:04 PM. |
![]() |
![]() |
![]() |
#6 |
VIP Member
Join Date: Feb 2014
Location: Derby City, USA
Posts: 3,663
Likes: 1,094
Liked 8,216 Times in 1,537 Posts
|
![]()
Check to make sure that carb linkage is opening all the way.....
|
![]() |
![]() |
![]() |
#7 |
Member
Join Date: Sep 2011
Location: Oklahoma City, OK
Posts: 215
Likes: 3
Liked 7 Times in 5 Posts
|
![]()
god i could only dream its something as simple as some crossed plug wires.
|
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: Jun 2011
Location: Ga.
Posts: 521
Likes: 7
Liked 13 Times in 11 Posts
|
![]()
With that cam timing you should have pumped up about 210lbs of compression. That would be where I would have started. If not then you either don't have the compression you thought you did or the cam timing is way off.........somehow.
And as you may have already guessed , if the PTV was checked it would have been checked AFTER the cam was "phased" the way you want it.....so that was check point 1 for correct cam install. If the PTV is where it should be , you would have very little "wiggle" room to move it around and definitely no room to be a "tooth" off. Last edited by joespanova; 05-17-2017 at 08:37 AM. |
![]() |
![]() |
![]() |
#9 | |
Senior Member
Join Date: Jan 2007
Location: N/A
Posts: 882
Likes: 0
Liked 22 Times in 22 Posts
|
![]() Quote:
__________________
don,t have one |
|
![]() |
![]() |
![]() |
#10 |
VIP Member
Join Date: Feb 2014
Location: Derby City, USA
Posts: 3,663
Likes: 1,094
Liked 8,216 Times in 1,537 Posts
|
![]()
Old batteries ? I know at least one prominent stock Eliminator racer that freshened his motor and later found that a weak battery was the culprit.....
|
![]() |
![]() |
![]() |
|
|