|
|
11-24-2023, 09:32 PM
|
#1 |
|
Member
Join Date: Mar 2002
Location: Brownstown, Mi 48134
Posts: 196
Likes: 35
Liked 13 Times in 7 Posts
|
Wanted suggestions how to create low drag Wilwood brakes
Guys,
I'm looking for suggestions on how to create low drag brakes. I have Wilwood 4 piston caliper brakes front & rear on my Gen 3 GT/DA 92 Camaro. Is there a kit one can buy? The TDM brakes are out of the question. Thanks for looking, |
|
|
|
11-24-2023, 11:03 PM
|
#2 |
|
VIP Member
Join Date: Jun 2009
Location: Boulder City, Nevada 89005
Posts: 2,708
Likes: 2,732
Liked 2,398 Times in 679 Posts
|
Re: Wanted suggestions how to create low drag Wilwood brake
I shim the caliber with spacer to make sure they are centered
on the disc properly (usually they are not). They still have more drag than the more expensive brands that my son runs on his cars!
__________________
John Irving 741 Stock 741 Super Stock |
|
|
|
| Liked |
|
11-25-2023, 06:51 AM
|
#3 |
|
Member
Join Date: Jun 2007
Location: NJ
Posts: 350
Likes: 62
Liked 126 Times in 61 Posts
|
Re: Wanted suggestions how to create low drag Wilwood brake
As well as making sure the caliper is center I have small stiff springs I put between the pads so the cotter pin holds the springs in place.
|
|
|
|
| Liked |
|
11-25-2023, 09:40 AM
|
#4 | |
|
VIP Member
Join Date: Nov 2007
Location: New Jersey
Posts: 2,628
Likes: 160
Liked 758 Times in 379 Posts
|
Re: Wanted suggestions how to create low drag Wilwood brake
Quote:
|
|
|
|
|
| Liked |
|
11-25-2023, 10:06 AM
|
#5 | |
|
VIP Member
Join Date: Feb 2014
Location: Derby City, USA
Posts: 3,562
Likes: 1,057
Liked 7,574 Times in 1,460 Posts
|
Re: Wanted suggestions how to create low drag Wilwood brake
Quote:
Last edited by MR DERBY CITY; 11-25-2023 at 10:48 AM. |
|
|
|
|
| Liked |
|
11-25-2023, 10:15 AM
|
#6 |
|
VIP Member
Join Date: Nov 2007
Location: New Jersey
Posts: 2,628
Likes: 160
Liked 758 Times in 379 Posts
|
Re: Wanted suggestions how to create low drag Wilwood brake
there's good reason why you won't find wilwood brakes installed on any car built for drag racing by a professional chassis shop
|
|
|
|
| Liked |
|
11-25-2023, 11:14 AM
|
#7 |
|
Member
Join Date: May 2011
Location: Auburndale,Florida
Posts: 220
Likes: 27
Liked 71 Times in 38 Posts
|
Re: Wanted suggestions how to create low drag Wilwood brake
Doesn’t Wilwood offer a low drag “ o” ring to replace the square cut seals in the calipers?
|
|
|
|
| Liked |
|
11-25-2023, 11:24 AM
|
#8 |
|
Senior Member
Join Date: Jun 2011
Location: Ga.
Posts: 521
Likes: 7
Liked 13 Times in 11 Posts
|
Re: Wanted suggestions how to create low drag Wilwood brake
Making sure the calipers are centered is a no brainer , but switching to drilled rotors was the best thing I did. No more drag. This and the right pads.
Mine are Wilwood. |
|
|
|
| Liked |
|
11-25-2023, 12:05 PM
|
#9 | |
|
Member
Join Date: Mar 2002
Location: Brownstown, Mi 48134
Posts: 196
Likes: 35
Liked 13 Times in 7 Posts
|
Re: Wanted suggestions how to create low drag Wilwood brake
Quote:
I did look yesterday and I did'nt see any. I will call Monday. Thanks for the reply, |
|
|
|
|
|
11-25-2023, 12:12 PM
|
#10 | |
|
Member
Join Date: Mar 2002
Location: Brownstown, Mi 48134
Posts: 196
Likes: 35
Liked 13 Times in 7 Posts
|
Re: Wanted suggestions how to create low drag Wilwood brake
Quote:
What have you been up to? I have seen you post in a long time. Do you still have the Firebird? |
|
|
|
|
 |
|
|
Linear Mode
