Jerico clutch sensor?

Nmbr1GMfan · 12-11-2017, 01:36 PM

Anyone know someone I can send the bearing retainer to for the installation of a Racepak clutch sensor? Thanks.

Tom Broome · 12-11-2017, 11:44 PM

Have you checked out this thread?
Stockers make it difficult to have the sensor in the bearing retainer.
http://classracer.com/classforum/sho...=clutch+sensor

Nmbr1GMfan · 12-12-2017, 09:48 AM

Thanks Tom, I had seen that and the only person that implied he might make a kit I have PMed. Thanks.

Jim Hawkins · 12-12-2017, 10:56 PM

When I added a data recorder with my Jerico I did not see anyway to have it read off of the input. Not enough room. I had a split collar made which installed on the cluster with a magnet in it. Drilled a hole in the case and made a adjustable sleeve to mount the sensor. The cluster is not turning at the same rpm as the input so that difference has to be calibrated in to get a accurate input reading.

Nmbr1GMfan · 12-13-2017, 09:16 AM

Thanks for the help everyone, I have been informed by a member here that Rob at Advanced has a kit for a collar and a drill guide, ordered it yesterday. I'll update this when it gets installed for future info.

Sean Marconette · 12-13-2017, 01:52 PM

Todd,
Does that put the sensor in the bellhousing on the candlestick? That's where mine is on my GF5-R. When removing/reinstalling the trans I have to be careful as I have broken the sensor before. Also use adel clamps or cush clamps to hold the cable to the candlestick and away from the TOB.

Sean

Nmbr1GMfan · 12-13-2017, 03:57 PM

Quote:

Originally Posted by Sean Marconette

Todd,
Does that put the sensor in the bellhousing on the candlestick? That's where mine is on my GF5-R. When removing/reinstalling the trans I have to be careful as I have broken the sensor before. Also use adel clamps or cush clamps to hold the cable to the candlestick and away from the TOB.

Sean

Sensor is in the side of the trans.

Scatpack1 · 12-19-2017, 10:49 PM

Sorry to hijack, but why would you need a clutch sensor? What is its purpose?

james schaechter · 12-20-2017, 05:03 AM

The biggest reason is to show what the clutch is doing and when. Clutches need to slip to be effective, but when, how much and how long they slip is a big deal. You can know exactly what happened and adjust tuning and driving to improve very quickly with a racepak or similar data acquisition system and a good clutch sensor.

Matt S · 12-25-2017, 10:36 PM

To those who have installed the magnet in the input shaft, how deep did you spotface the input shaft to install the magnet? Full depth of the magnet, or less?

12-11-2017, 01:36 PM	#1
Nmbr1GMfan VIP Member Join Date: Aug 2013 Posts: 1,763 Likes: 1,197 Liked 1,954 Times in 491 Posts	Jerico clutch sensor? Anyone know someone I can send the bearing retainer to for the installation of a Racepak clutch sensor? Thanks. __________________ Todd Greene Last edited by Nmbr1GMfan; 12-11-2017 at 01:38 PM.

12-11-2017, 11:44 PM	#2
Tom Broome Member Join Date: Sep 2009 Posts: 137 Likes: 78 Liked 78 Times in 40 Posts	Re: Jerico clutch sensor? Have you checked out this thread? Stockers make it difficult to have the sensor in the bearing retainer. http://classracer.com/classforum/sho...=clutch+sensor

12-12-2017, 09:48 AM	#3
Nmbr1GMfan VIP Member Join Date: Aug 2013 Posts: 1,763 Likes: 1,197 Liked 1,954 Times in 491 Posts	Re: Jerico clutch sensor? Thanks Tom, I had seen that and the only person that implied he might make a kit I have PMed. Thanks. __________________ Todd Greene

12-12-2017, 10:56 PM	#4
Jim Hawkins Member Join Date: Jan 2010 Posts: 193 Likes: 87 Liked 114 Times in 34 Posts	Re: Jerico clutch sensor? When I added a data recorder with my Jerico I did not see anyway to have it read off of the input. Not enough room. I had a split collar made which installed on the cluster with a magnet in it. Drilled a hole in the case and made a adjustable sleeve to mount the sensor. The cluster is not turning at the same rpm as the input so that difference has to be calibrated in to get a accurate input reading.

12-13-2017, 09:16 AM	#5
Nmbr1GMfan VIP Member Join Date: Aug 2013 Posts: 1,763 Likes: 1,197 Liked 1,954 Times in 491 Posts	Re: Jerico clutch sensor? Thanks for the help everyone, I have been informed by a member here that Rob at Advanced has a kit for a collar and a drill guide, ordered it yesterday. I'll update this when it gets installed for future info. __________________ Todd Greene

12-13-2017, 01:52 PM	#6
Sean Marconette Senior Member Join Date: Mar 2006 Posts: 976 Likes: 780 Liked 274 Times in 76 Posts	Re: Jerico clutch sensor? Todd, Does that put the sensor in the bellhousing on the candlestick? That's where mine is on my GF5-R. When removing/reinstalling the trans I have to be careful as I have broken the sensor before. Also use adel clamps or cush clamps to hold the cable to the candlestick and away from the TOB. Sean __________________ Sean Marconette 84 Mustang 5060 SS/N

12-19-2017, 10:49 PM	#8
Scatpack1 Junior Member Join Date: Jun 2008 Location: Tennessee Posts: 4 Likes: 0 Liked 0 Times in 0 Posts	Re: Jerico clutch sensor? Sorry to hijack, but why would you need a clutch sensor? What is its purpose? Last edited by Scatpack1; 12-19-2017 at 11:06 PM.

12-20-2017, 05:03 AM	#9
james schaechter VIP Member Join Date: Dec 2004 Location: Cumming GA Posts: 1,976 Likes: 1,261 Liked 1,384 Times in 288 Posts	Re: Jerico clutch sensor? The biggest reason is to show what the clutch is doing and when. Clutches need to slip to be effective, but when, how much and how long they slip is a big deal. You can know exactly what happened and adjust tuning and driving to improve very quickly with a racepak or similar data acquisition system and a good clutch sensor. __________________ James Schaechter 3163 STK

12-25-2017, 10:36 PM	#10
Matt S Junior Member Join Date: Apr 2006 Posts: 98 Likes: 0 Liked 20 Times in 12 Posts	Re: Jerico clutch sensor? To those who have installed the magnet in the input shaft, how deep did you spotface the input shaft to install the magnet? Full depth of the magnet, or less?