SBC guide plate ?

rod · 08-26-2015, 07:53 PM

I have at least one pushrod guide plate, which needs to be split to get the rocker square on the valve stem.
since I assume these plates are hard, probably a band saw will not work [or will it?]. what is the best and or easiest way to split a plate?

Thanks Rod in AZ

SSDiv6 · 08-26-2015, 08:00 PM

Quote:

Originally Posted by rod

I have at least one pushrod guide plate, which needs to be split to get the rocker square on the valve stem.
since I assume these plates are hard, probably a band saw will not work [or will it?]. what is the best and or easiest way to split a plate?

Thanks Rod in AZ

Band saw has always worked for me. After you set them properly in place, weld them together in place to prevent any movement.

ss3011 · 08-26-2015, 08:10 PM

An abrasive cutoff wheel works well. You can get them pretty thin (1/16 0r 1/32} x 4" .

Alan Roehrich · 08-26-2015, 08:57 PM

They make slotted adjustable guide plates for the small block Chevy. You simply move them where you need them, and tack them with a welder (I suggest TIG).

rod · 08-26-2015, 10:40 PM

thanks for the help/ answers.
this leads to another question. these are GM/Chevy 292 heads and were tapped at the factory, and the plates are all machine stamped. how is it that they are off. you would think they would be all right on.

Rod in AZ

Sam Ehret · 08-26-2015, 11:23 PM

Why not make your own guide plate? You can water jet them or mill them if you have a bridgeport. If you need them hardened, make them from 01 or A2 and flame harden with a torch. You will have a set exactly the way you want them.

Alan Nyhus · 08-27-2015, 08:20 AM

The Isky adjustable guide plates work well. AFR and Comp Cams also make 'em.

08-26-2015, 07:53 PM	#1
rod Member Join Date: Dec 2009 Location: Kingman, NW AZ. in the middle of the longest stretch of Route 66 Posts: 314 Likes: 0 Liked 20 Times in 15 Posts	SBC guide plate ? I have at least one pushrod guide plate, which needs to be split to get the rocker square on the valve stem. since I assume these plates are hard, probably a band saw will not work [or will it?]. what is the best and or easiest way to split a plate? Thanks Rod in AZ

08-26-2015, 08:10 PM	#3
ss3011 Senior Member Join Date: Feb 2002 Location: Southeast Michigan Posts: 909 Likes: 70 Liked 239 Times in 114 Posts	Re: SBC guide plate ? An abrasive cutoff wheel works well. You can get them pretty thin (1/16 0r 1/32} x 4" .

08-26-2015, 08:57 PM	#4
Alan Roehrich Veteran Member Join Date: May 2006 Location: Murfreesboro TN Posts: 5,105 Likes: 1,564 Liked 1,789 Times in 408 Posts	Re: SBC guide plate ? They make slotted adjustable guide plates for the small block Chevy. You simply move them where you need them, and tack them with a welder (I suggest TIG). __________________ Alan Roehrich 212A G/S

08-26-2015, 10:40 PM	#5
rod Member Join Date: Dec 2009 Location: Kingman, NW AZ. in the middle of the longest stretch of Route 66 Posts: 314 Likes: 0 Liked 20 Times in 15 Posts	Re: SBC guide plate ? thanks for the help/ answers. this leads to another question. these are GM/Chevy 292 heads and were tapped at the factory, and the plates are all machine stamped. how is it that they are off. you would think they would be all right on. Rod in AZ

08-26-2015, 11:23 PM	#6
Sam Ehret Junior Member Join Date: Jul 2014 Posts: 18 Likes: 4 Liked 0 Times in 0 Posts	Re: SBC guide plate ? Why not make your own guide plate? You can water jet them or mill them if you have a bridgeport. If you need them hardened, make them from 01 or A2 and flame harden with a torch. You will have a set exactly the way you want them.

08-27-2015, 08:20 AM	#7
Alan Nyhus VIP Member Join Date: Dec 2002 Location: Lower Dakota territory Posts: 1,180 Likes: 1,074 Liked 799 Times in 236 Posts	Re: SBC guide plate ? The Isky adjustable guide plates work well. AFR and Comp Cams also make 'em. __________________ "That'll never work....."