|
|
03-21-2016, 08:14 PM
|
#1 |
|
VIP Member
Join Date: Jul 2008
Location: Liberty City [East Texas]
Posts: 1,760
Likes: 5
Liked 99 Times in 60 Posts
|
SBC EFI fuel rails
I am in need of SBC EFI fuel rails that have conventional SBC port spacing with #10 AN O ring threads at each end
__________________
Larry Woodfin 471W |
|
|
|
03-21-2016, 09:16 PM
|
#2 |
|
VIP Member
Join Date: Jul 2008
Location: Liberty City [East Texas]
Posts: 1,760
Likes: 5
Liked 99 Times in 60 Posts
|
Re: SBC EFI fuel rails
Edelbrock #3630 has 3/8 pipe thread so I can use adapters to #10 AN.
That is the best option I see so far
__________________
Larry Woodfin 471W |
|
|
|
|
03-21-2016, 09:35 PM
|
#3 |
|
VIP Member
Join Date: Jul 2008
Location: Liberty City [East Texas]
Posts: 1,760
Likes: 5
Liked 99 Times in 60 Posts
|
Re: SBC EFI fuel rails
this shows a factory fuel rail test fit. It does not have enough material to thread 3/8" pipe.
__________________
Larry Woodfin 471W |
|
|
|
|
03-21-2016, 09:43 PM
|
#4 |
|
Veteran Member
Join Date: Mar 2005
Location: Sand Springs, OK
Posts: 8,132
Likes: 896
Liked 390 Times in 170 Posts
|
Re: SBC EFI fuel rails
This your Super Stock engine? If so, why would you need -10 lines?
__________________
Ed Wright 4156 SS/JA |
|
|
|
|
03-21-2016, 10:02 PM
|
#5 |
|
VIP Member
Join Date: Jul 2008
Location: Liberty City [East Texas]
Posts: 1,760
Likes: 5
Liked 99 Times in 60 Posts
|
Re: SBC EFI fuel rails
Ed,
it is our 417" SBC bracket engine. Fuel cell, fuel filter, fuel pump, fuel regulator all #10 Holley EFI system
__________________
Larry Woodfin 471W |
|
|
|
|
03-21-2016, 10:05 PM
|
#6 |
|
VIP Member
Join Date: Jul 2008
Location: Liberty City [East Texas]
Posts: 1,760
Likes: 5
Liked 99 Times in 60 Posts
|
Re: SBC EFI fuel rails
Ed,
we are definitely form one extreme to the other. With the Super 10 I am installing a 4GC
__________________
Larry Woodfin 471W |
|
|
|
|
03-21-2016, 10:57 PM
|
#7 |
|
Member
Join Date: Nov 2012
Location: Denver Co
Posts: 408
Likes: 282
Liked 35 Times in 17 Posts
 |
Re: SBC EFI fuel rails
Not sure it will help...
What about a weld on fitting? That is how I did mine this last go around... http://www.locashdyno.com/store2/ind...roducts_id=324
__________________
Ross Gregory 5133 Stock,Super Stock 53 Top Dragster |
|
|
|
|
03-21-2016, 11:16 PM
|
#8 |
|
VIP Member
Join Date: Jun 2006
Posts: 3,420
Likes: 529
Liked 333 Times in 180 Posts
|
Re: SBC EFI fuel rails
Larry --check your emails good contact info Dick
|
|
|
|
 |
|
|
Linear Mode
